1980 Craftsman Chainsaw Gas Pumping Nightmare Unveiled!

Craftsman Chainsaw Won’t Pump Gas

Your 1980 Craftsman chainsaw is a reliable tool that has served you well for many years. But now, it’s not pumping gas and you’re not sure what to do. Don’t worry, you’re not alone. This is a common problem with older chainsaws. In this article, I’ll walk you through the steps to troubleshoot and fix the problem so you can get back to cutting wood.

1980 Craftman Chainsaw Won’T Pump Gas

1980 Craftsman Chainsaw Gas Pumping Nightmare:

1980 Craftsman chainsaws have a design flaw that causes the gas pump to become clogged with sawdust, preventing the engine from starting. To fix this problem, you need to remove the gas tank and clean the pump assembly.

1980 Craftsman Chainsaw Won’t Pump Gas

Symptoms

If your 1980 Craftsman chainsaw won’t pump gas, you may experience the following symptoms:

The chainsaw won’t start
The chainsaw starts but then dies immediately
The chainsaw starts and runs for a few seconds, but then dies
The chainsaw starts and runs, but the engine cuts out when you apply the throttle

Causes

There are a number of possible causes for a 1980 Craftsman chainsaw not pumping gas, including:

A clogged fuel filter
A dirty or damaged fuel line
A faulty fuel pump
A problem with the carburetor
A problem with the ignition system

Solutions

To fix a 1980 Craftsman chainsaw that won’t pump gas, you will need to identify the cause of the problem and then take the appropriate steps to fix it.

Clogged fuel filter:

If the fuel filter is clogged, you will need to remove it and clean it or replace it.

Dirty or damaged fuel line:

If the fuel line is dirty or damaged, you will need to replace it.

Faulty fuel pump:

If the fuel pump is faulty, you will need to replace it.

Problem with the carburetor:

If the carburetor is dirty or damaged, you will need to clean it or rebuild it.

Problem with the ignition system:

If the ignition system is faulty, you will need to have it repaired or replaced.

Prevention

To prevent your 1980 Craftsman chainsaw from not pumping gas, you can take the following steps:

Keep the fuel filter clean and replace it regularly.
Keep the fuel line clean and free of kinks.
Use fresh fuel.
Store the chainsaw in a cool, dry place.
Avoid running the chainsaw out of gas.

Conclusion

If your 1980 Craftsman chainsaw won’t pump gas, you can troubleshoot the problem and fix it yourself or take it to a qualified repair shop. By following the tips in this article, you can keep your chainsaw running smoothly and safely.

Also Read: 1980 Craftsman Chainsaw Won’T Pump Gas

FAQs: 1980 Craftsman Chainsaw Won’t Pump Gas

Why won’t my 1980 Craftsman chainsaw pump gas?

There are a few possible reasons why your 1980 Craftsman chainsaw won’t pump gas. Here are the most common:

The fuel line is clogged: This is the most common cause of a chainsaw not pumping gas. The fuel line can become clogged with dirt, dust, or other debris, which prevents the gas from flowing to the carburetor. To fix this problem, you will need to clean the fuel line.

The carburetor is dirty: The carburetor is responsible for mixing the air and fuel in the correct proportions. If the carburetor is dirty, it can cause the chainsaw to not pump gas. To fix this problem, you will need to clean the carburetor.

The fuel filter is clogged: The fuel filter is located between the gas tank and the carburetor. It helps to prevent dirt and debris from entering the carburetor. If the fuel filter is clogged, it can prevent the gas from flowing to the carburetor. To fix this problem, you will need to replace the fuel filter.

The spark plug is fouled: The spark plug is responsible for igniting the fuel in the combustion chamber. If the spark plug is fouled, it can cause the chainsaw to not start or run properly. To fix this problem, you will need to clean or replace the spark plug.

The engine is flooded: If the engine is flooded, it can prevent the chainsaw from starting. This can happen if you accidentally put too much gas in the carburetor. To fix this problem, you will need to turn the chainsaw off and let it sit for a few minutes. You can also try to clear the carburetor by spraying it with carburetor cleaner.

How do I fix a clogged fuel line on a 1980 Craftsman chainsaw?

To fix a clogged fuel line on a 1980 Craftsman chainsaw, you will need to:

1. Remove the fuel tank cap.
2. Locate the fuel line. It is a small, black hose that connects the gas tank to the carburetor.
3. Use a pair of pliers to disconnect the fuel line from the carburetor.
4. Hold the fuel line over a bucket and carefully pour some carburetor cleaner through it.
5. Reattach the fuel line to the carburetor.
6. Refill the gas tank.
7. Start the chainsaw and let it run for a few minutes to clear the fuel line.

How do I clean a dirty carburetor on a 1980 Craftsman chainsaw?

To clean a dirty carburetor on a 1980 Craftsman chainsaw, you will need to:

1. Remove the carburetor from the chainsaw.
2. Locate the carburetor bowl. It is a small, round bowl that is located at the bottom of the carburetor.
3. Remove the carburetor bowl.
4. Use a carburetor cleaner to clean the inside of the carburetor bowl.
5. Reattach the carburetor bowl.
6. Reinstall the carburetor on the chainsaw.

How do I replace the fuel filter on a 1980 Craftsman chainsaw?

To replace the fuel filter on a 1980 Craftsman chainsaw, you will need to:

1. Remove the fuel tank cap.
2. Locate the fuel filter. It is a small, cylindrical filter that is located between the gas tank and the carburetor.
3. Use a pair of pliers to disconnect the fuel line from the fuel filter.
4. Remove the fuel filter.
5. Install a new fuel filter.
6. Reattach the fuel line to the fuel filter.
7. Refill the gas tank.

How do I clean a fouled spark plug on a 1980 Craftsman chainsaw?

To clean a fouled spark plug on a 1980 Craftsman chainsaw, you will need to:

1. Remove the spark plug from the chainsaw.
2. Use a spark plug wrench to unscrew the spark plug.
3. Dip a clean rag in carburetor cleaner.
4. Use the rag to clean the spark plug electrodes.
5. Reinstall the spark plug.

How do I clear a flooded engine on a 1980 Craftsman chainsaw?

To clear a flooded engine on a 1980 Craftsman chainsaw, you will need to:

1. Turn the chainsaw off and let it sit for a few minutes.