How to Fix a 1980 Craftsman Chainsaw That Won’t Pump Gas

Craftsman Chainsaw Won’t Pump Gas 5 Quick Fixes

Your 1980 Craftsman chainsaw is a reliable tool that has served you well for many years. But now, it’s not pumping gas and you’re not sure what to do. Don’t worry, you’re not alone. This is a common problem with older chainsaws. In this article, I’ll show you five quick fixes that will get your chainsaw up and running again in no time.

1980 Craftsman Chainsaw Won’T Pump Gas

How to Fix a 1980 Craftsman Chainsaw That Won’t Pump Gas

1. Disconnect the spark plug wire.
2. Remove the air filter cover.
3. Use a small screwdriver to pry up the choke lever.
4. Pull the starter rope until you see gas come out of the carburetor.
5. Replace the air filter cover and reconnect the spark plug wire.
6. Try starting the chainsaw.

1980 Craftsman Chainsaw Won’t Pump Gas

Symptoms

There are a few symptoms that may indicate that your 1980 Craftsman chainsaw won’t pump gas. These include:

The chainsaw won’t start
The chainsaw starts but dies immediately
The chainsaw starts and runs for a few seconds, then dies
The chainsaw starts and runs, but the engine sputters and stalls

Causes

There are a number of possible causes for a 1980 Craftsman chainsaw not pumping gas. These include:

A clogged fuel filter
A dirty carburetor
A faulty fuel pump
A bad spark plug
A faulty ignition switch

Solutions

The solution to a 1980 Craftsman chainsaw not pumping gas will depend on the underlying cause. If the problem is a clogged fuel filter, you can clean or replace the filter. If the carburetor is dirty, you can clean it. If the fuel pump is faulty, you will need to replace it. If the spark plug is bad, you will need to replace it. If the ignition switch is faulty, you will need to replace it.

Prevention

You can prevent a 1980 Craftsman chainsaw from not pumping gas by following these tips:

Keep the fuel filter clean
Clean the carburetor regularly
Replace the fuel pump as needed
Replace the spark plug as needed
Replace the ignition switch as needed

Conclusion

If your 1980 Craftsman chainsaw won’t pump gas, you can troubleshoot the problem and fix it yourself. If you are not comfortable working on your chainsaw, you can take it to a qualified repair shop.

Also Read: Chainsaw Won T Start After Running Out Of Gas

FAQs: 1980 Craftsman Chainsaw Won’t Pump Gas

Why won’t my 1980 Craftsman chainsaw pump gas?

There are a few possible reasons why your 1980 Craftsman chainsaw won’t pump gas.

The fuel line is clogged: This is the most common cause of a chainsaw not pumping gas. To check if the fuel line is clogged, remove the fuel tank cap and look inside the tank. If you see any debris or sediment, you will need to clean the fuel line.

The fuel filter is clogged: The fuel filter is located between the fuel tank and the carburetor. If the fuel filter is clogged, it will prevent gas from flowing to the carburetor. To check if the fuel filter is clogged, remove it from the chainsaw and inspect it for debris. If the filter is clogged, you will need to replace it.

The carburetor is dirty or damaged: The carburetor is responsible for mixing air and fuel in the correct proportions. If the carburetor is dirty or damaged, it will not be able to mix the air and fuel properly, which will cause the chainsaw to not run properly. To check if the carburetor is dirty or damaged, you will need to remove it from the chainsaw and inspect it. If the carburetor is dirty, you will need to clean it. If the carburetor is damaged, you will need to replace it.

The spark plug is fouled: The spark plug is responsible for igniting the fuel mixture in the cylinder. If the spark plug is fouled, it will not be able to ignite the fuel mixture, which will cause the chainsaw to not run properly. To check if the spark plug is fouled, you will need to remove it from the chainsaw and inspect it. If the spark plug is fouled, you will need to clean it or replace it.

The air filter is dirty: The air filter is located between the carburetor and the engine. If the air filter is dirty, it will restrict the flow of air to the carburetor, which will cause the chainsaw to not run properly. To check if the air filter is dirty, you will need to remove it from the chainsaw and inspect it. If the air filter is dirty, you will need to clean it.

How do I fix a 1980 Craftsman chainsaw that won’t pump gas?

To fix a 1980 Craftsman chainsaw that won’t pump gas, you will need to identify the cause of the problem and then fix it.

If the fuel line is clogged, you will need to clean the fuel line. To do this, you will need to remove the fuel tank cap and disconnect the fuel line from the carburetor. Then, you will need to use a small brush or pipe cleaner to clean out the fuel line. Once the fuel line is clean, you can reconnect it to the carburetor and fill the fuel tank.

If the fuel filter is clogged, you will need to replace the fuel filter. To do this, you will need to remove the old fuel filter from the chainsaw and install a new one. Once the new fuel filter is installed, you can fill the fuel tank.

If the carburetor is dirty or damaged, you will need to clean or replace the carburetor. To clean the carburetor, you will need to remove it from the chainsaw and disassemble it. Then, you will need to use a carburetor cleaner to clean the carburetor parts. Once the carburetor is clean, you can reassemble it and install it on the chainsaw. If the carburetor is damaged, you will need to replace it.

If the spark plug is fouled, you will need to clean or replace the spark plug. To clean the spark plug, you will need to remove it from the chainsaw and use a spark plug cleaner to clean the electrodes. Once the spark plug is clean, you can reinstall it in the chainsaw. If the spark plug is damaged, you will need to replace it.

If the air filter is dirty, you will need to clean the air filter. To do this, you will need to remove the air filter from the chainsaw and use a vacuum cleaner to clean it. Once the air filter is clean, you can reinstall it in the chainsaw.

What are the symptoms of a 1980 Craftsman chainsaw that won’t pump gas?

The symptoms of a 1980 Craftsman chainsaw that won’t pump gas include:

The chainsaw will not start.
The chainsaw will start but will not run smoothly.
The chainsaw will run but will not produce power.
The chainsaw will run but will not stay running.