Automatic Oiler On Chainsaw Not Working: [Solved]

As a chainsaw owner, there’s nothing more frustrating than having your automatic oiler stop working. Not only can it lead to damage to your chainsaw, but it can also be a major inconvenience. After all, you don’t want to have to stop what you’re doing to manually oil your chainsaw every few minutes.

If your automatic oiler isn’t working, there are a few things you can check to try to troubleshoot the problem. In this guide, I’ll walk you through the steps on how to diagnose and resolve the issue so that you can get your chainsaw back up and running in no time.

I understand that this issue can be a major pain, but I’m confident that by following the steps in this guide, you’ll be able to get your chainsaw up and running again in no time.

Most Common Reasons Why Automatic Oiler On Chainsaw Not Working

1. Oiler Pump Not Working

The oiler pump may not be working if it is clogged with debris, the oil level is too low, or the pump is damaged.
To check if the oiler pump is working, turn on the chainsaw and listen for the pump to cycle. You should be able to hear a faint whirring sound.
If you do not hear the pump cycling, you can try cleaning the pump with a small brush or needle. If that does not work, you may need to replace the pump.

2. Oiler Hose Clogged

The oiler hose may be clogged with debris, preventing oil from reaching the chain.
To check if the oiler hose is clogged, remove the hose from the chainsaw and inspect it for obstructions.
If the hose is clogged, you can try clearing it with a small brush or needle. If that does not work, you may need to replace the hose.

3. Oiler Tube Clogged

The oiler tube may be clogged with debris, preventing oil from reaching the chain.
To check if the oiler tube is clogged, remove the tube from the chainsaw and inspect it for obstructions.
If the tube is clogged, you can try clearing it with a small brush or needle. If that does not work, you may need to replace the tube.

4. Oil Level Too Low

If the oil level in the chainsaw is too low, the oiler will not be able to pump enough oil to the chain.
To check the oil level, remove the oil cap and look at the oil level. The oil level should be between the full and add marks on the dipstick.
If the oil level is low, add oil to the chainsaw until the level reaches the full mark.

5. Oil Filter Clogged

The oil filter may be clogged with debris, preventing oil from reaching the chain.
To check if the oil filter is clogged, remove the filter from the chainsaw and inspect it for obstructions.
If the filter is clogged, you can try cleaning it with a small brush or needle. If that does not work, you may need to replace the filter.

How to Troubleshoot: Automatic Oiler on Chainsaw Not Working

Check the Oil Reservoir

If your chainsaw’s automatic oiler is not working
the first step is to check the oil reservoir. Ensure that it is filled with the appropriate bar and chain oil. Sometimes
the oiler may not work due to low oil levels or clogs in the reservoir.

Inspect the Oil Lines

Next
inspect the oil lines for any blockages or kinks. These can impede the flow of oil to the bar and chain
causing the automatic oiler to malfunction. Use a small wire or compressed air to clear any obstructions in the oil lines.

Examine the Oil Pump

The oil pump is a crucial component of the automatic oiler system. If the oil pump is faulty or worn out
it can lead to oiling issues. Check the oil pump for any signs of damage or wear
and replace it if necessary.

Adjust the Oiler Settings

Sometimes
the automatic oiler may not be dispensing enough oil due to incorrect settings. Refer to the chainsaw’s manual to locate the oiler adjustment screw. By turning this screw
you can regulate the amount of oil being dispensed to the bar and chain.

Inspect the Oiler Worm Gear

The oiler worm gear is responsible for delivering oil to the bar and chain. If this component is damaged or worn
it can cause the automatic oiler to malfunction. Inspect the oiler worm gear for any signs of wear and tear
and replace it if necessary.

Clean the Oil Ports

Over time
oil ports can become clogged with sawdust
debris
or hardened oil. Use a small brush or compressed air to clean the oil ports thoroughly. Ensuring that the oil ports are clear will help maintain proper oil flow to the bar and chain.

Final Checks

After performing the troubleshooting steps mentioned above
it’s essential to perform a final check. Start the chainsaw and observe whether the automatic oiler is now functioning correctly. If the issue persists
it may be necessary to seek professional assistance to diagnose and rectify the problem.

Conclusion

Troubleshooting an automatic oiler that is not working on a chainsaw

FAQs: Automatic Oiler on Chainsaw Not Working

Why isn’t my chainsaw’s automatic oiler working?

There are a few possible reasons why your chainsaw’s automatic oiler might not be working. Here are a few of the most common:

The oiler is not properly installed. Make sure that the oiler is installed correctly and that the oil line is not kinked or blocked.
The oiler is not getting enough oil. Check the oil level in the reservoir and make sure that it is full. If the oil level is low, add more oil to the reservoir.
The oiler is clogged. The oiler can become clogged with sawdust or other debris. To clean the oiler, remove the oiler cover and clean the inside of the oiler with a small brush.
The oiler is not working properly. If the oiler is not working properly, it may need to be replaced.

How do I fix a chainsaw’s automatic oiler?

To fix a chainsaw’s automatic oiler, you will need to identify the problem and then take the appropriate steps to fix it. Here are the steps to fix a chainsaw’s automatic oiler:

1. Identify the problem. The first step is to identify the problem with the oiler. This can be done by checking the oil level in the reservoir, inspecting the oiler for damage, and checking the oiler for clogs.
2. Fix the problem. Once you have identified the problem, you can fix it. If the oil level is low, add more oil to the reservoir. If the oiler is clogged, clean the oiler with a small brush. If the oiler is not working properly, it may need to be replaced.

How often should I oil my chainsaw?

The frequency with which you should oil your chainsaw depends on the type of chainsaw you have and the conditions in which you are using it. However, as a general rule, you should oil your chainsaw after every 5-10 hours of use.

What type of oil should I use for my chainsaw?

The type of oil you should use for your chainsaw depends on the type of chainsaw you have. However, as a general rule, you should use a high-quality, 2-cycle oil.

What happens if I don’t oil my chainsaw?

If you don’t oil your chainsaw, it can cause a number of problems, including:

The chain will become dull and will not cut as well.
The chain will wear out faster.
The engine will overheat and may be damaged.
The chainsaw may be difficult to start.

Also Read: Battery Driven Chainsaw Oiler Not Working

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *