Black And Decker Hedge Trimmer Cord Won’T Pull [With Solution]

Dealing with a Black and Decker hedge trimmer with a cord that won’t pull can be incredibly frustrating. It’s the kind of problem that can halt your yard work plans and leave you feeling stuck. But fear not
as we’re here to help you troubleshoot and resolve this common issue. In this guide
we’ll walk you through the step-by-step process of diagnosing and fixing the cord pull problem
so you can get back to shaping your hedges with ease. Let’s dive in and get your hedge trimmer back in action.

Reasons Why Black And Decker Hedge Trimmer Cord Won’T Pull

Cord Tangling

The most common reason for a Black and Decker hedge trimmer cord not to pull is that it is tangled. This can happen if the cord is not properly spooled onto the reel, or if it becomes caught on something while the trimmer is in use. To fix this problem, first unplug the trimmer and then carefully untangle the cord. Be sure to spool the cord back onto the reel in a neat and orderly fashion.

Cord Breakage

Another common cause of a trimmer cord not to pull is that it has broken. This can happen if the cord is subjected to too much stress, such as if it is caught on a branch or other object. To fix this problem, you will need to replace the cord. To do this, first unplug the trimmer and then remove the old cord from the reel. Then, install the new cord by threading it through the hole in the reel and securing it with the retaining clip.

Cord Slipping

In some cases, the trimmer cord may not be pulling because it is slipping out of the drive gear. This can happen if the gear is worn or damaged, or if the cord is not properly seated in the gear. To fix this problem, you will need to remove the drive gear and inspect it for wear or damage. If the gear is damaged, it will need to be replaced. If the cord is not properly seated in the gear, you will need to adjust it so that it is properly engaged.

Cord Corrosion

Finally, a trimmer cord may not be pulling because it is corroded. This can happen if the cord is exposed to moisture for an extended period of time. To fix this problem, you will need to remove the cord from the trimmer and clean it with a de-rusting solution. Once the cord is clean, you will need to apply a corrosion-resistant coating to it.

How to Troubleshoot: Black & Decker Hedge Trimmer Cord Won’t Pull

Symptoms

The trimmer won’t start when you pull the cord.
The trimmer starts, but the motor dies after a few seconds.
The trimmer starts and runs, but the cord won’t rewind.

Causes

There are a few possible causes for a Black & Decker hedge trimmer cord that won’t pull.

The cord is tangled or kinked:
If the cord is tangled or kinked, it can prevent the trimmer from starting. To fix this, untangle or straighten the cord.

The cord is damaged:
If the cord is damaged, it may not be able to conduct electricity properly. To check for damage, inspect the cord for cuts, tears, or fraying. If you find any damage, replace the cord.

The starter switch is stuck:
The starter switch is a small lever that engages the starter motor. If the starter switch is stuck, it can prevent the trimmer from starting. To check for a stuck starter switch, try to move the lever back and forth. If the lever is stuck, you may need to replace it.

The starter motor is bad:
If the starter motor is bad, it won’t be able to engage the trimmer’s engine. To check for a bad starter motor, try to start the trimmer without using the starter cord. If the trimmer starts, the starter motor is bad.

The engine is bad:
If the engine is bad, it won’t be able to run. To check for a bad engine, try to start the trimmer without using the starter cord. If the trimmer doesn’t start, the engine is bad.

Solutions

Once you’ve identified the cause of the problem, you can fix it.

To fix a tangled or kinked cord, untangle or straighten the cord.

To fix a damaged cord, replace the cord.

To fix a stuck starter switch, try to move the lever back and forth. If the lever is still stuck, you may need to replace it.

To fix a bad starter motor, replace the starter motor.

To fix a bad engine, replace the engine.

Prevention

To prevent problems with your Black & Decker hedge trimmer cord, you can take a few steps to prevent damage.

Keep the cord away from sharp objects:
The cord can be damaged if it comes into contact with sharp objects, such as rocks or branches.

Don’t pull the cord too hard:
Pulling the cord too hard can damage the cord.

Store the trimmer in a safe place:
When you’re not using the trimmer, store it in a safe place where it won’t be damaged.

By following these tips, you can help to prevent problems with your Black & Decker hedge trimmer cord.

Also Read: Black And Decker Hedge Trimmer Does Not Work

FAQs: Black and Decker Hedge Trimmer Cord Won’t Pull

Why won’t my Black and Decker hedge trimmer cord pull?

There are a few possible reasons why your Black and Decker hedge trimmer cord won’t pull. Here are some of the most common:

The cord is damaged: If the cord is damaged, it may not be able to conduct electricity properly. This can prevent the trimmer from starting.

The cord is not plugged in all the way: Make sure that the cord is plugged into the trimmer and into an outlet securely.

The outlet is not working: Try plugging the trimmer into a different outlet to see if that fixes the problem.

The trimmer is not turned on: Make sure that the trimmer is turned on.

The trimmer’s switch is stuck: Try turning the trimmer off and on again to see if that fixes the problem.

How do I fix a damaged Black and Decker hedge trimmer cord?

If the cord is damaged, you can try to fix it yourself. Here are the steps:

1. Turn off the trimmer and unplug it from the outlet.
2. Use a sharp knife or scissors to cut the damaged section of the cord off.
3. Strip about 1 inch of insulation off of each end of the cord.
4. Twist the bare copper wires together and wrap them with electrical tape.
5. Reattach the cord to the trimmer.

If you are not comfortable doing this yourself, you can take the trimmer to a qualified repair shop.

How do I make sure the cord is plugged in all the way?

To make sure the cord is plugged in all the way, follow these steps:

1. Look at the plug. The prongs should be completely inserted into the outlet.
2. Push the plug in until you hear a click.
3. Try to pull the plug out. If it is difficult to remove, the plug is plugged in all the way.

What do I do if the outlet is not working?

If the outlet is not working, you can try to fix it yourself or you can call an electrician. Here are the steps to fix a faulty outlet:

1. Turn off the power to the outlet.
2. Remove the cover plate from the outlet.
3. Look at the outlet. The two slots should be black and the round hole should be copper.
4. If any of the wires are loose or damaged, replace them.
5. Tighten the screws on the outlet.
6. Replace the cover plate.

If you are not comfortable doing this yourself, you can call an electrician.

How do I turn on the trimmer?

To turn on the trimmer, follow these steps:

1. Press the power button.
2. The trimmer will start to vibrate.
3. Use the trigger to adjust the speed of the trimmer.

How do I fix a stuck trimmer switch?

To fix a stuck trimmer switch, follow these steps:

1. Turn off the trimmer and unplug it from the outlet.
2. Use a small screwdriver to pry the switch open.
3. Clean the switch with a dry cloth.
4. Reassemble the switch.
5. Plug the trimmer back in and turn it on.

If the switch is still stuck, you can take the trimmer to a qualified repair shop.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *