Briggs And Stratton Pressure Washer Pump Not Working: [Causes & Proven Solutions]

A Briggs and Stratton pressure washer is a powerful tool that can be used for a variety of tasks, from cleaning driveways to washing cars. However, when the pump on a Briggs and Stratton pressure washer stops working, it can be a major inconvenience. Not only is it frustrating to be unable to use your pressure washer, but it can also be dangerous if you try to use it without the pump working properly.

This troubleshooting guide will help you quickly diagnose and resolve the issue of a . By following the steps in this guide, you can get your pressure washer back up and running in no time.

Most Common Reasons Briggs And Stratton Pressure Washer Pump Not Working

Most Common Reasons

1. No water flow

Cause:
The most common reason for no water flow is a clogged filter. To check the filter, remove it from the pump and inspect it for debris. If the filter is clogged, clean it or replace it with a new one.

Solution:
To clear a clogged filter, remove it from the pump and rinse it under running water. If the filter is damaged, replace it with a new one.

2. Low water pressure

Cause:
Low water pressure can be caused by a number of factors, including:

A clogged nozzle:
To check the nozzle, remove it from the gun and inspect it for debris. If the nozzle is clogged, clean it or replace it with a new one.

A restricted hose:
To check the hose, inspect it for kinks or bends. If the hose is kinked or bent, straighten it out.

A faulty pump:
If the pump is faulty, it will not be able to generate enough pressure to produce a strong water stream. To test the pump, turn on the pressure washer and listen for the pump to run. If the pump is not running, it will need to be repaired or replaced.

3. The pump is overheating

Cause:
The pump can overheat if it is used for too long at a high pressure. To prevent the pump from overheating, take frequent breaks and allow the pump to cool down.

Solution:
To prevent the pump from overheating, do not use it for more than 30 minutes at a time. Allow the pump to cool down for at least 10 minutes before using it again.

4. The pump is leaking

Cause:
The pump can leak if there is a problem with the seals. To check for leaks, inspect the pump for any signs of fluid coming out. If you find a leak, you will need to replace the seals.

Solution:
To fix a leak, you will need to remove the pump from the pressure washer and replace the seals. You can purchase replacement seals at most hardware stores.

How to Troubleshoot: Briggs and Stratton Pressure Washer Pump Not Working

Symptoms of a Briggs and Stratton Pressure Washer Pump Not Working

There are a few different symptoms that may indicate that your Briggs and Stratton pressure washer pump is not working properly. These include:

The pressure washer is not producing any pressure.

The pressure washer is producing low pressure.

The pressure washer is making a loud whining or buzzing noise.

The pressure washer is leaking fluid.

The pressure washer is smoking.

Troubleshooting a Briggs and Stratton Pressure Washer Pump

If you are experiencing any of the symptoms listed above, it is important to troubleshoot the problem in order to determine the cause and fix it. Here are a few steps to help you troubleshoot your Briggs and Stratton pressure washer pump:

1. Check the power supply:
Make sure that the pressure washer is plugged in and turned on. If it is not, plug it in and turn it on.

2. Check the water supply:
Make sure that there is water in the tank and that the water hose is connected to the pump and to the water source.3. Check the air filter:
Remove the air filter and clean it with a brush. If the air filter is clogged, it can restrict the flow of air to the pump and cause it to overheat.

4. Check the oil level:
Make sure that the oil level in the pump is correct. If the oil level is low, it can cause the pump to overheat.

5. Check the pump belt:
Inspect the pump belt for wear and tear. If the belt is damaged, it will need to be replaced.

6. Check the pump housing:
Look for any cracks or damage to the pump housing. If the pump housing is damaged, it will need to be replaced.

7. Check the pump impeller:
Remove the pump impeller and inspect it for wear and tear. If the impeller is damaged, it will need to be replaced.

Conclusion

By following these steps, you can troubleshoot a Briggs and Stratton pressure washer pump and determine the cause of the problem. Once you have determined the cause of the problem, you can fix it and get your pressure washer back up and running.

Also Read: Briggs And Stratton Pressure Washer Soap Dispenser Not Working

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *