Briggs And Stratton Pressure Washer Soap Not Working [Try This Proven Fixes]

Your Briggs and Stratton pressure washer is one of the most valuable tools in your arsenal for cleaning your home and property. But when the soap isn’t working, it can be a major inconvenience. Not only is it frustrating, but it can also be time-consuming and expensive to fix.

In this guide, I’ll show you how to troubleshoot a Briggs and Stratton pressure washer that’s not dispensing soap. I’ll cover the most common causes of this problem, as well as the steps you can take to fix it. By the end of this guide, you’ll be able to get your pressure washer back up and running in no time.

Reasons Why Briggs And Stratton Pressure Washer Soap Not Working

Reasons Why Briggs And Stratton Pressure Washer Soap Not Working

Incorrect soap:
The soap you are using may not be compatible with your pressure washer. Make sure to use a soap that is specifically designed for pressure washers.

Incorrect dilution:
The soap you are using may be too concentrated or too diluted. The manufacturer’s instructions will specify the correct dilution ratio.

Clogged soap nozzle:
The soap nozzle can become clogged with soap residue, preventing the soap from being sprayed out of the pressure washer. To clean the soap nozzle, remove it from the pressure washer and soak it in a vinegar solution for several minutes.

Blocked detergent inlet:
The detergent inlet can become blocked with soap residue, preventing the soap from being drawn into the pressure washer. To clean the detergent inlet, remove the detergent cup and clean it with a brush.

Low water pressure:
The water pressure may be too low to properly atomize the soap, resulting in a soapy mess. To increase the water pressure, check the water supply hose for kinks or blockages. You may also need to increase the water pressure at the source, such as by turning up the water pressure regulator on your home’s water heater.

Faulty soap pump:
The soap pump may be faulty, preventing it from properly pumping the soap out of the pressure washer. If you suspect that the soap pump is faulty, you will need to have it repaired or replaced.

How to Troubleshoot: Briggs and Stratton Pressure Washer Soap Not Working

Symptoms

The soap dispenser on your Briggs and Stratton pressure washer is not dispensing soap.
The soap is not coming out of the wand when you press the trigger.
The soap is coming out of the wand in a weak stream.
The soap is not mixing with the water properly.

Causes

There are a few possible causes for a Briggs and Stratton pressure washer soap not working.

The soap dispenser is clogged:
This is the most common cause of a soap not working. The soap dispenser can become clogged with soap residue, dirt, or debris.

The soap reservoir is empty:
If the soap reservoir is empty, the soap won’t be able to dispense.

The soap is the wrong viscosity:
The soap should be a thin, watery consistency. If the soap is too thick, it won’t be able to flow through the dispenser properly.

The soap is too old:
Old soap can become thick and clumpy, and it won’t be able to dispense properly.

The pressure washer is not turned on:
Make sure that the pressure washer is turned on and that the soap dispenser is engaged.

The soap dispenser is not working properly:
The soap dispenser may be broken or damaged. If the soap dispenser is not working properly, it will need to be replaced.

Solutions

Here are a few solutions for a Briggs and Stratton pressure washer soap not working.

Clean the soap dispenser:
To clean the soap dispenser, remove the soap reservoir from the pressure washer. Use a small brush to clean out any soap residue, dirt, or debris from the dispenser.

Fill the soap reservoir:
Make sure that the soap reservoir is full of soap.

Use the right viscosity of soap:
Use a thin, watery consistency of soap.

Use fresh soap:
Use fresh soap that is not too old.

Turn on the pressure washer:
Make sure that the pressure washer is turned on and that the soap dispenser is engaged.

Replace the soap dispenser:
If the soap dispenser is not working properly, it will need to be replaced.

Prevention

Here are a few things you can do to prevent a Briggs and Stratton pressure washer soap from not working.

Clean the soap dispenser regularly:
Cleaning the soap dispenser regularly will help to prevent it from becoming clogged.

Use the right viscosity of soap:
Using the right viscosity of soap will help to ensure that it flows through the dispenser properly.

Use fresh soap:
Using fresh soap will help to prevent it from becoming thick and clumpy.

Turn off the pressure washer when not in use:
Turning off the pressure washer when not in use will help to prevent the soap dispenser from becoming damaged.

Conclusion

If your Briggs and Stratton pressure washer soap is not working, there are a few things you can do to troubleshoot the problem. You can clean the soap dispenser, fill the soap reservoir, use the right viscosity of soap, use fresh soap, turn on the pressure washer, and replace the soap dispenser. You can also prevent a Briggs and Stratton pressure washer soap from not working by cleaning the soap dispenser regularly, using the right viscosity of soap, using fresh soap, and turning off the pressure washer when not in use.

Also Read: Briggs Stratton Pressure Washer 020338-0 Not Working

FAQs: Briggs and Stratton Pressure Washer Soap Not Working

Why is my Briggs and Stratton pressure washer soap not working?

There are a few reasons why your Briggs and Stratton pressure washer soap might not be working. Here are some of the most common causes:

The soap container is empty: Make sure that the soap container is filled with soap and that the lid is tightly closed.

The soap dispenser is clogged: If the soap dispenser is clogged, it will not be able to dispense soap properly. To clean the soap dispenser, remove the lid and rinse it out with warm water. You can also use a small brush to remove any stubborn debris.

The soap is too thick: If the soap is too thick, it will not be able to flow through the soap dispenser properly. To thin the soap, add a small amount of water to the soap container.

The pressure washer is not turned on: Make sure that the pressure washer is turned on and that the soap dispenser is turned on.

How do I fix my Briggs and Stratton pressure washer soap not working?

To fix your Briggs and Stratton pressure washer soap not working, try the following steps:

1. Check the soap container to make sure that it is filled with soap and that the lid is tightly closed.
2. Clean the soap dispenser if it is clogged.
3. Thin the soap if it is too thick.
4. Turn on the pressure washer and the soap dispenser.

If you have tried these steps and your pressure washer soap is still not working, you may need to contact a qualified technician for help.

What type of soap should I use in my Briggs and Stratton pressure washer?

You should use a pressure washer soap that is specifically designed for use with pressure washers. These soaps are typically made with a high concentration of surfactants, which help to break down dirt and grime. They are also designed to be safe for use on a variety of surfaces, including concrete, brick, and siding.

Some common types of pressure washer soaps include:

Alkaline soaps: These soaps are typically made with a high concentration of sodium hydroxide, which is a strong base. Alkaline soaps are effective at removing tough dirt and grime, but they can also be corrosive to some surfaces.

Acidic soaps: These soaps are typically made with a high concentration of phosphoric acid, which is a weak acid. Acidic soaps are less effective at removing tough dirt and grime than alkaline soaps, but they are less corrosive to surfaces.

Neutral soaps: These soaps are typically made with a balanced pH, which makes them safe for use on all surfaces. Neutral soaps are not as effective at removing tough dirt and grime as alkaline or acidic soaps, but they are a good choice for people who are concerned about the corrosive effects of harsh chemicals.

How much soap should I use in my Briggs and Stratton pressure washer?

The amount of soap you use in your Briggs and Stratton pressure washer will depend on the size of the surface you are cleaning and the level of dirt and grime that needs to be removed.

As a general rule, you should use about 1 ounce of soap per gallon of water. However, you may need to use more or less soap depending on the specific conditions.

If you are not sure how much soap to use, it is always better to start with a small amount and add more as needed.

What happens if I use too much soap in my Briggs and Stratton pressure washer?

If you use too much soap in your Briggs and Stratton pressure washer, it can cause a number of problems, including:

Clogging the soap dispenser: If the soap is too thick, it can clog the soap dispenser and prevent it from dispensing soap properly.

Creating a soapy mess: If you use too much soap, it can create a soapy mess that is difficult to clean up.

Damaging the pressure washer: If the soap is too harsh, it can damage the seals and gaskets in the pressure washer.

It is important to use the correct amount of soap in your Briggs and Stratton pressure washer to avoid these problems.