Why Your Chainsaw Won’t Start After Running Out of Gas

Chainsaw Won’t Start After Running Out of Gas

Running out of gas in the middle of a chainsaw project is a frustrating experience. But don’t despair, there are a few things you can check to get your chainsaw running again.

In this blog post, we’ll walk you through the steps to troubleshoot a chainsaw that won’t start after running out of gas. We’ll also provide tips on how to prevent this from happening in the future.

Chainsaw Won T Start After Running Out Of Gas

Why Your Chainsaw Won’t Start After Running Out of Gas

When a chainsaw runs out of gas, the carburetor can become flooded with fuel. This can prevent the chainsaw from starting when you try to restart it. To fix this problem, you will need to clear the carburetor.

To clear the carburetor, you will need to remove the air filter and the spark plug. Then, you will need to use a small screwdriver to turn the carburetor adjustment screw counterclockwise until the fuel flows out of the carburetor. Once the fuel starts to flow, you can turn the screw clockwise until the flow stops.

Once you have cleared the carburetor, you can reinstall the air filter and the spark plug. Then, you can try to start the chainsaw. The chainsaw should start without any problems.

Chainsaw Won’t Start After Running Out of Gas

What to Do

If your chainsaw won’t start after running out of gas, there are a few things you can check and try.

Check the fuel tank:
Make sure that the fuel tank is full and that the fuel valve is open.

Clean the carburetor:
If the carburetor is dirty, it can prevent the chainsaw from starting. To clean the carburetor, you will need to remove it from the chainsaw and disassemble it. Then, use a carburetor cleaner to clean the jets and passages.

Replace the spark plug:
If the spark plug is fouled, it can also prevent the chainsaw from starting. To replace the spark plug, you will need to remove the old spark plug and install a new one.

Check the air filter:
If the air filter is dirty, it can restrict the flow of air to the carburetor and cause the chainsaw to not start. To clean the air filter, you will need to remove it from the chainsaw and rinse it with warm water.

Adjust the carburetor:
If the carburetor is not adjusted properly, it can prevent the chainsaw from starting. To adjust the carburetor, you will need to use a carburetor adjustment tool.

Troubleshooting Tips

If you have tried the steps above and your chainsaw still won’t start, here are a few troubleshooting tips:

Try starting the chainsaw with a different type of fuel. If you are using a gasoline-powered chainsaw, try using a different brand of gasoline. If you are using a two-stroke oil-and-gas mixture, try using a different brand of oil.
Try starting the chainsaw in a different location. If you are trying to start the chainsaw in a cold environment, try moving it to a warmer location.
Try starting the chainsaw with a different spark plug. If you are using a new spark plug, try using an older spark plug.
Try starting the chainsaw with a different air filter. If you are using a new air filter, try using an older air filter.
Try adjusting the carburetor again. If you have already adjusted the carburetor, try adjusting it again.

Conclusion

If you have tried all of the steps above and your chainsaw still won’t start, it is best to take it to a qualified chainsaw repair shop. A qualified technician will be able to diagnose the problem and repair the chainsaw properly.

Also Read: Chainsaw Won’T Draw Gas

FAQs: Chainsaw Won’t Start After Running Out of Gas

Why won’t my chainsaw start after running out of gas?

There are a few reasons why your chainsaw might not start after running out of gas.

The carburetor is flooded: When you run out of gas, the carburetor can become flooded with fuel. This can prevent the chainsaw from starting because the fuel can’t get to the engine. To fix this, you can try to clear the carburetor by following the instructions in your chainsaw’s owner’s manual.

The spark plug is fouled: The spark plug is responsible for igniting the fuel in the engine. If the spark plug is fouled, it can’t properly ignite the fuel, which will prevent the chainsaw from starting. To fix this, you can try cleaning the spark plug with a wire brush. If the spark plug is damaged, you will need to replace it.

The air filter is dirty: The air filter helps to keep dirt and debris out of the engine. If the air filter is dirty, it can restrict airflow to the engine, which can prevent the chainsaw from starting. To fix this, you can try cleaning the air filter with a vacuum cleaner. If the air filter is damaged, you will need to replace it.

The engine is seized: If the engine is seized, it means that the pistons are stuck and can’t move. This can prevent the chainsaw from starting. To fix this, you will need to take the chainsaw to a qualified technician.

What should I do if my chainsaw won’t start after running out of gas?

If your chainsaw won’t start after running out of gas, you can try the following steps:

1. Check the carburetor to make sure it’s not flooded.
2. Check the spark plug to make sure it’s not fouled.
3. Check the air filter to make sure it’s not dirty.
4. Try starting the chainsaw again.
5. If the chainsaw still won’t start, take it to a qualified technician.

How can I prevent my chainsaw from not starting after running out of gas?

You can prevent your chainsaw from not starting after running out of gas by following these tips:

Keep the carburetor clean: A dirty carburetor can prevent the chainsaw from starting. To keep the carburetor clean, you can try cleaning it with a carburetor cleaner according to the instructions in your chainsaw’s owner’s manual.

Replace the spark plug regularly: A fouled spark plug can prevent the chainsaw from starting. To prevent this, you can try replacing the spark plug according to the recommendations in your chainsaw’s owner’s manual.

Clean the air filter regularly: A dirty air filter can restrict airflow to the engine, which can prevent the chainsaw from starting. To prevent this, you can try cleaning the air filter according to the recommendations in your chainsaw’s owner’s manual.

Don’t run the chainsaw out of gas: Running the chainsaw out of gas can damage the carburetor and other parts of the engine. To prevent this, you can try to avoid running the chainsaw out of gas.

What are the signs that my chainsaw is about to run out of gas?

There are a few signs that your chainsaw is about to run out of gas. These signs include:

The chainsaw starts to lose power.
The chainsaw starts to make a sputtering sound.
The chainsaw starts to stall.

If you see any of these signs, it’s time to refuel your chainsaw.

What should I do if my chainsaw runs out of gas while I’m using it?

If your chainsaw runs out of gas while you’re using it, you can try the following steps:

1. Turn off the chainsaw.
2. Remove the spark plug.
3. Pour a small amount of gas into the carburetor bowl.
4. Reinstall the spark plug.
5. Start the chainsaw.

If the chainsaw still won’t start, you can try the following steps:

1. Check the carburetor to make sure it’s not flooded.
2. Check the spark plug to make sure it’s not fouled.
3. Check the air filter to make sure it’s not dirty.
4. Try starting the chainsaw again.
5. If the chainsaw still won’t start, take it to a qualified technician.