Craftsman Chainsaw Automatic Oiler Not Working: [Fixed]

As a chainsaw owner, there are few things more frustrating than having your saw’s automatic oiler stop working. Not only can this lead to damage to the saw itself, but it can also be a safety hazard. After all, a chainsaw that is not properly lubricated is more likely to overheat and cause a fire.

If your Craftsman chainsaw automatic oiler is not working, there are a few things you can check to try to troubleshoot the problem. In this guide, I will walk you through the steps of diagnosing and resolving this common issue. By the end of this guide, you should be able to get your saw’s automatic oiler working again in no time.

Most Common Reasons Why Craftsman Chainsaw Automatic Oiler Not Working

1. Oiler Hose Kinked or Clogged

The oiler hose can become kinked or clogged, preventing oil from reaching the chain. To check for a kinked hose, look for a bend or kink in the hose where it is attached to the chainsaw or the oil tank. If you find a kink, straighten it out as best you can. To check for a clogged hose, remove the hose from the chainsaw and inspect it for debris. If you find debris, clean it out with a small brush or needle.

2. Oiler Pump Not Working

The oiler pump is responsible for pumping oil to the chain. If the pump is not working, the chain will not be lubricated properly. To check if the pump is working, start the chainsaw and listen for the pump to run. You should be able to hear a faint buzzing sound coming from the pump. If you do not hear a sound, the pump may be broken and will need to be replaced.

3. Oil Level Too Low

If the oil level in the tank is too low, the oiler will not be able to pump enough oil to the chain. To check the oil level, remove the oil cap and look at the oil level. The oil level should be between the full and add marks on the dipstick. If the oil level is below the add mark, add more oil to the tank.

4. Oil Filter Clogged

The oil filter can become clogged with debris, preventing oil from reaching the chain. To check the oil filter, remove it from the chainsaw and inspect it for debris. If you find debris, clean the filter with a small brush or needle.

5. Oil Pump O-Ring Damaged

The oil pump O-ring is a small rubber ring that seals the oil pump to the chainsaw. If the O-ring is damaged, it can leak oil and cause the chain to become dry. To check the O-ring, remove the oil pump from the chainsaw and inspect the O-ring for damage. If the O-ring is damaged, replace it.

How to Troubleshoot: Craftsman Chainsaw Automatic Oiler Not Working

Symptoms of a Craftsman Chainsaw Automatic Oiler Not Working

There are a few telltale signs that your Craftsman chainsaw automatic oiler is not working properly. These include:

The saw is running hot, even when it is not under heavy load.
The bar and chain are not being lubricated properly, which can lead to damage.
The oil reservoir is empty or nearly empty, even though you have recently filled it.
The oiler is making a strange noise or is not functioning at all.

Troubleshooting a Craftsman Chainsaw Automatic Oiler

If you suspect that your Craftsman chainsaw automatic oiler is not working properly, there are a few things you can do to troubleshoot the problem.

Check the oil level. The first thing you should do is check the oil level in the reservoir. If the reservoir is empty or nearly empty, fill it up with the appropriate type of oil.
Check the oil line. The oil line runs from the reservoir to the bar and chain. Make sure that the line is not kinked or damaged. If it is, replace it with a new one.
Check the oil pump. The oil pump is responsible for pumping oil from the reservoir to the bar and chain. If the pump is not working properly, it will not be able to lubricate the saw properly. You can check the pump by removing the oil line from the bar and chain. If no oil comes out, the pump is not working properly and will need to be replaced.
Check the oil filter. The oil filter helps to keep dirt and debris out of the oil system. If the filter is clogged, it will restrict the flow of oil to the bar and chain. You can check the filter by removing it from the oil pump. If the filter is clogged, clean it or replace it with a new one.

Preventing Craftsman Chainsaw Automatic Oiler Problems

The best way to prevent problems with your Craftsman chainsaw automatic oiler is to properly maintain it. This includes:

Checking the oil level regularly. Make sure to check the oil level in the reservoir every time you use the saw. If the level is low, fill it up with the appropriate type of oil.
Keeping the oil line free of kinks and damage. Make sure that the oil line is not kinked or damaged. If it is, replace it with a new one.
Cleaning the oil filter regularly. The oil filter should be cleaned or replaced regularly, depending on the manufacturer’s recommendations.

By following these tips, you can help to prevent problems with your Craftsman chainsaw automatic oiler and keep your saw running smoothly.

FAQs: Craftsman Chainsaw Automatic Oiler Not Working

Why is my Craftsman chainsaw automatic oiler not working?

There are a few possible reasons why your Craftsman chainsaw automatic oiler may not be working. Here are some of the most common causes:

The oiler is not turned on. Make sure that the oiler is turned on and that the oil level is correct.
The oiler is clogged. The oiler can become clogged with sawdust or other debris, which can prevent it from working properly. To clean the oiler, remove the oiler cover and clean the inside of the oiler with a soft cloth.
The oiler is not getting enough oil. The oiler may not be getting enough oil if the oil reservoir is empty or if the oil line is blocked. To check the oil reservoir, remove the oil cap and check the level of oil. If the oil reservoir is empty, fill it with oil. To check the oil line, remove the oiler cover and look for any blockages.
The oiler is not working properly. If the oiler is not working properly, it may need to be replaced.

How do I fix my Craftsman chainsaw automatic oiler?

To fix your Craftsman chainsaw automatic oiler, you will need to identify the cause of the problem. Once you have identified the cause of the problem, you can follow the steps below to fix it:

If the oiler is not turned on, turn it on and check the oil level.
If the oiler is clogged, clean the oiler with a soft cloth.
If the oiler is not getting enough oil, fill the oil reservoir or clear the oil line.
If the oiler is not working properly, replace the oiler.

How often should I oil my Craftsman chainsaw?

You should oil your Craftsman chainsaw every 20 minutes of use. You can also oil the chainsaw before and after each use.

What kind of oil should I use for my Craftsman chainsaw?

You should use a high-quality chainsaw oil that is designed for use with two-stroke engines. Some good options include:

Bar and chain oil: This type of oil is specifically designed for use with chainsaws. It is typically a light oil that will not gum up the chain or the bar.
Synthetic oil: Synthetic oil is a good option for chainsaws that are used in harsh conditions. It is a more durable oil that will not break down as quickly as other types of oil.
Mineral oil: Mineral oil is a good option for chainsaws that are used in less harsh conditions. It is a less expensive oil than synthetic oil.

How do I adjust the oiler on my Craftsman chainsaw?

To adjust the oiler on your Craftsman chainsaw, you will need to follow these steps:

1. Turn off the chainsaw and remove the spark plug.
2. Locate the oiler adjustment screw. It is typically located on the side of the chainsaw.
3. Turn the oiler adjustment screw clockwise to increase the oil flow or counterclockwise to decrease the oil flow.
4. Reinstall the spark plug and start the chainsaw.
5. Test the oil flow by running the chainsaw for a few minutes. The oil should be dripping onto the chain at a steady rate.

If the oil flow is not correct, adjust the oiler adjustment screw again until the oil flow is correct.

Also Read: Craftsman Chainsaw Bar Oil Not Working