Craftsman Pressure Washer Clean And Carry Pump Not Working [Easy Steps]

Your Craftsman pressure washer is a powerful tool that can help you clean your home, driveway, and other outdoor surfaces. But when the clean and carry pump isn’t working, it can be a major inconvenience. Not only is it frustrating to not be able to use your pressure washer, but it can also be dangerous. If the pump isn’t working properly, it can spray water in the wrong direction or at too high of a pressure, which can cause damage to your property or even injury to yourself.

In this guide, I’ll show you how to troubleshoot a Craftsman pressure washer clean and carry pump that isn’t working. I’ll walk you through the steps to identify the problem and fix it quickly and easily. So if you’re ready to get your pressure washer back up and running, keep reading!

Reasons Why Craftsman Pressure Washer Clean And Carry Pump Not Working

Clogged Inlet Filter

The inlet filter is located on the bottom of the pressure washer and prevents dirt and debris from entering the pump. If the filter is clogged, it will restrict the flow of water to the pump and cause it to overheat. To clean the filter, remove it from the pressure washer and rinse it under warm water.

Low Water Pressure

If the water pressure is low, it may be due to a problem with the water supply, the pump, or the hose. To check the water supply, make sure that the water is turned on and that the pressure is adequate. To check the pump, remove the inlet hose from the pump and see if water flows freely. To check the hose, inspect it for leaks.

Faulty Pump

If the pump is faulty, it will not be able to generate enough pressure to power the pressure washer. To check the pump, remove the inlet hose from the pump and turn on the pressure washer. If the pump does not make any noise or if the pressure is very low, the pump is likely faulty.

Clogged Orifice

The orifice is a small hole in the nozzle that controls the flow of water. If the orifice is clogged, it will restrict the flow of water and cause the pressure washer to lose power. To clean the orifice, remove the nozzle from the pressure washer and use a small wire to clear the blockage.

Damaged Hose

If the hose is damaged, it will not be able to withstand the high pressure of the water and it may burst. To check the hose, inspect it for cracks or tears. If the hose is damaged, it should be replaced.

How to Troubleshoot: Craftsman Pressure Washer Clean and Carry Pump Not Working

Symptoms

There are a few symptoms that may indicate that your Craftsman pressure washer clean and carry pump is not working properly. These include:

The pressure washer is not producing any pressure.
The pressure washer is making a whining or buzzing noise.
The pressure washer is leaking water.
The pressure washer is overheating.

Causes

There are a number of potential causes for a Craftsman pressure washer clean and carry pump not working properly. These include:

A clogged filter.
A faulty pump.
A damaged hose.
A problem with the electrical system.

Troubleshooting

To troubleshoot the problem with your Craftsman pressure washer clean and carry pump, you will need to first identify the cause of the problem. Here are a few steps to help you do this:

1. Check the filter. If the filter is clogged, it will prevent the pump from generating enough pressure. To check the filter, remove it from the pump and inspect it for any debris. If the filter is clogged, clean it with warm water and a mild detergent.
2. Check the pump. If the pump is faulty, it will not be able to generate enough pressure. To check the pump, turn on the pressure washer and listen for any unusual noises. If the pump is making a whining or buzzing noise, it is likely faulty. You will need to replace the pump.
3. Check the hose. If the hose is damaged, it will leak water and prevent the pump from generating enough pressure. To check the hose, inspect it for any cracks or tears. If the hose is damaged, you will need to replace it.
4. Check the electrical system. If there is a problem with the electrical system, it will prevent the pump from turning on. To check the electrical system, turn on the pressure washer and look for any warning lights or error codes. If you see any warning lights or error codes, you will need to have the pressure washer serviced by a qualified technician.

Prevention

There are a few things you can do to prevent problems with your Craftsman pressure washer clean and carry pump:

Keep the filter clean.
Inspect the pump regularly for any signs of wear or damage.
Replace the hose regularly if it becomes damaged.
Have the pressure washer serviced regularly by a qualified technician.

By following these tips, you can help to keep your Craftsman pressure washer clean and carry pump in good working order.

Also Read: Craftsman Pressure Washer Sopdipenser Not Working

FAQs: Craftsman Pressure Washer Clean and Carry Pump Not Working

Why is my Craftsman pressure washer clean and carry pump not working?

There are a few possible reasons why your Craftsman pressure washer clean and carry pump may not be working. Here are some of the most common causes:

The pump is clogged: If the pump is clogged with dirt or debris, it will not be able to generate enough pressure to power the spray nozzle. To fix this problem, you will need to clean the pump according to the manufacturer’s instructions.

The pump is overheating: If the pump is overheating, it will shut down automatically to prevent damage. To prevent this problem, you should make sure that the pump is not running for too long at a time and that it is getting enough airflow.

The pump is damaged: If the pump is damaged, it will not be able to generate enough pressure to power the spray nozzle. To fix this problem, you will need to replace the pump.

How do I clean the pump on my Craftsman pressure washer?

To clean the pump on your Craftsman pressure washer, you will need to follow these steps:

1. Turn off the pressure washer and disconnect the power cord.
2. Remove the pump cover.
3. Use a brush to clean the inside of the pump housing.
4. Remove the check valve and clean it with a small brush.
5. Reassemble the pump and replace the pump cover.

How do I prevent my Craftsman pressure washer pump from overheating?

To prevent your Craftsman pressure washer pump from overheating, you should follow these tips:

Do not run the pump for too long at a time: The pump should not be run for more than 30 minutes at a time.

Make sure that the pump is getting enough airflow: The pump should be located in a well-ventilated area.

Do not allow the pump to get too hot: If the pump feels hot to the touch, it is overheating and should be turned off.

How do I replace the pump on my Craftsman pressure washer?

To replace the pump on your Craftsman pressure washer, you will need to follow these steps:

1. Turn off the pressure washer and disconnect the power cord.
2. Remove the pump cover.
3. Remove the old pump.
4. Install the new pump.
5. Reassemble the pump and replace the pump cover.

What are the signs of a bad pump on a Craftsman pressure washer?

There are a few signs that may indicate that the pump on your Craftsman pressure washer is bad. These include:

The pressure washer is not generating enough pressure.
The pressure washer is making a loud noise.
The pressure washer is leaking fluid.
The pressure washer is overheating.

If you notice any of these signs, it is important to have the pump checked by a qualified technician.