Dolmar Chainsaw Won’t Start? Here’s Why!
What to Do
Running out of gas in your Dolmar chainsaw can be a frustrating experience. But don’t worry, it’s usually an easy fix. In this blog post, we’ll walk you through the steps to troubleshoot and fix a Dolmar chainsaw that won’t start after running out of gas.
We’ll start by taking a look at the most common causes of this problem, and then we’ll provide step-by-step instructions on how to fix each one. By the end of this post, you’ll be able to get your Dolmar chainsaw up and running again in no time.
Dolmar Chainsaw Won’T Start After Running Out Of Gas
Dolmar Chainsaw Won’t Start? Here’s Why!
There are a few reasons why your Dolmar chainsaw might not start. Here are the most common ones:
Fuel problem:
Make sure that you have enough fuel in the tank and that the fuel is fresh. Also, check the fuel filter to make sure that it is clean.
Spark plug problem:
Check the spark plug to make sure that it is in good condition and that the gap is correct. If the spark plug is fouled, clean it or replace it.
Chainsaw chain too tight:
If the chainsaw chain is too tight, it can prevent the engine from starting. Loosen the chain until it can move freely.
Chainsaw bar not lubricated:
Make sure that the chainsaw bar is properly lubricated. If the bar is dry, it can cause the engine to seize up.
If you have checked all of these things and your chainsaw still won’t start, you may need to take it to a professional for repairs.
Dolmar Chainsaw Won’t Start After Running Out of Gas
What to Do
If your Dolmar chainsaw won’t start after running out of gas, there are a few things you can check and try.
Check the fuel tank:
Make sure that the fuel tank is full and that the fuel valve is open.
Clean the carburetor:
If the carburetor is dirty, it can prevent the chainsaw from starting. To clean the carburetor, you will need to remove it from the chainsaw and follow the manufacturer’s instructions.
Check the spark plug:
Make sure that the spark plug is clean and that the gap is correct. If the spark plug is dirty, you can clean it with a wire brush. If the gap is incorrect, you can adjust it with a spark plug gap tool.
Check the air filter:
Make sure that the air filter is clean. A dirty air filter can restrict the airflow to the carburetor and prevent the chainsaw from starting. To clean the air filter, you can remove it from the chainsaw and rinse it with warm water.
Troubleshooting Tips
If you have checked all of the above and your Dolmar chainsaw still won’t start, here are a few troubleshooting tips:
Try starting the chainsaw with a different type of gas. Some chainsaws are designed to run on a specific type of gas, and if you use a different type of gas, it can cause problems.
Try starting the chainsaw in a warm environment. If the chainsaw is cold, it can be harder to start.
Try starting the chainsaw with a different spark plug. If the spark plug is bad, it can prevent the chainsaw from starting.
Try starting the chainsaw with a different air filter. If the air filter is dirty, it can restrict the airflow to the carburetor and prevent the chainsaw from starting.
If you have tried all of the above and your Dolmar chainsaw still won’t start, it is best to take it to a qualified service technician for diagnosis and repair.
Prevention
To prevent your Dolmar chainsaw from not starting after running out of gas, you can take the following steps:
Keep the fuel tank full. This will help to prevent the carburetor from becoming dirty.
Clean the carburetor regularly. This will help to keep the carburetor working properly and prevent the chainsaw from not starting.
Check the spark plug regularly. Make sure that the spark plug is clean and that the gap is correct.
Check the air filter regularly. Make sure that the air filter is clean.
By following these tips, you can help to prevent your Dolmar chainsaw from not starting after running out of gas.
Also Read: Echo Chainsaw Won’T Start Gas From Muffler
FAQs: Dolmar Chainsaw Won’t Start After Running Out of Gas
Why won’t my Dolmar chainsaw start after running out of gas?
There are a few possible reasons why your Dolmar chainsaw won’t start after running out of gas.
The carburetor is flooded: When the chainsaw runs out of gas, the carburetor can become flooded with fuel. This can prevent the chainsaw from starting because the fuel can’t reach the spark plug. To fix this problem, you can try to clear the carburetor by following the instructions in your chainsaw’s owner’s manual.
The spark plug is fouled: The spark plug can become fouled if it is not properly gapped or if it is contaminated with dirt or oil. This can prevent the spark plug from generating a spark, which is necessary for the chainsaw to start. To fix this problem, you can try to clean the spark plug or replace it with a new one.
The air filter is dirty: The air filter can become dirty if it is not properly maintained. This can restrict the flow of air to the carburetor, which can cause the chainsaw to run poorly or not start at all. To fix this problem, you can try to clean the air filter or replace it with a new one.
The fuel filter is clogged: The fuel filter can become clogged if it is not properly maintained. This can prevent the fuel from reaching the carburetor, which can prevent the chainsaw from starting. To fix this problem, you can try to clean the fuel filter or replace it with a new one.
The chainsaw is not getting enough compression: The chainsaw may not be getting enough compression if the piston rings are worn or if the cylinder is damaged. This can prevent the chainsaw from starting because the compression is necessary to create the spark that ignites the fuel. To fix this problem, you may need to have the chainsaw repaired by a qualified technician.
What should I do if my Dolmar chainsaw won’t start after running out of gas?
If your Dolmar chainsaw won’t start after running out of gas, you should first try to identify the problem. You can do this by following the troubleshooting steps listed above. If you are unable to fix the problem yourself, you may need to have the chainsaw repaired by a qualified technician.
How can I prevent my Dolmar chainsaw from not starting after running out of gas?
There are a few things you can do to prevent your Dolmar chainsaw from not starting after running out of gas.
Make sure the carburetor is properly adjusted: A properly adjusted carburetor will help to ensure that the chainsaw gets the correct amount of fuel and air. This will help to prevent the chainsaw from flooding or running poorly.
Clean the spark plug regularly: A dirty spark plug can prevent the chainsaw from starting or running properly. To prevent this, you should clean the spark plug regularly.
Replace the air filter regularly: A dirty air filter can restrict the flow of air to the carburetor, which can cause the chainsaw to run poorly or not start at all. To prevent this, you should replace the air filter regularly.
Check the fuel filter regularly: A clogged fuel filter can prevent the fuel from reaching the carburetor, which can prevent the chainsaw from starting. To prevent this, you should check the fuel filter regularly and replace it if it is clogged.
Maintain the chainsaw properly: Proper maintenance of your Dolmar chainsaw will help to keep it running in good condition and prevent it from not starting after running out of gas. This includes things like changing the oil regularly, sharpening the chain, and inspecting the chainsaw for damage.
What if my Dolmar chainsaw still won’t start after trying all of these things?
If your Dolmar chainsaw still won’t start after trying all of the troubleshooting steps listed above, you may need to have the chainsaw repaired by a qualified technician.
Where can I find a qualified technician to repair my Dolmar chainsaw?
You can find a qualified technician to repair your Dolmar chainsaw by contacting your local Dolmar dealer or by searching online for Dolmar chainsaw repair services.