Earthwise 16 Corded Chainsaw Tooless Tensioning Not Working: [Reasons & Fixes]

As a chainsaw repair professional, I understand the frustration and inconvenience that can come with a chainsaw that is not functioning properly. One of the most common problems that I see is the . This can be a major inconvenience, as it can prevent you from using your chainsaw to cut through branches or other materials. In this guide, I will walk you through the steps to troubleshoot and resolve this issue. By the end of this guide, you will be able to get your chainsaw back up and running in no time.

Most Common Reasons Of Earthwise 16 Corded Chainsaw Tooless Tensioning Not Working

Most Common Reasons Of Earthwise 16 Corded Chainsaw Tooless Tensioning Not Working

1. The chain is too loose

If the chain is too loose, it will not be able to stay tight on the bar and will come off when you are using the chainsaw. To tighten the chain, follow these steps:

1. Turn the chainsaw off and remove the spark plug.
2. Use the chain tensioner to tighten the chain until it is snug against the bar.
3. Reinstall the spark plug and start the chainsaw.

2. The chain is too tight

If the chain is too tight, it will be difficult to operate the chainsaw and may cause damage to the chain or bar. To loosen the chain, follow these steps:

1. Turn the chainsaw off and remove the spark plug.
2. Use the chain tensioner to loosen the chain until it is slightly loose against the bar.
3. Reinstall the spark plug and start the chainsaw.

3. The chain oiler is not working

The chain oiler is responsible for lubricating the chain and bar. If the oiler is not working, the chain will become dry and will wear out faster. To check if the oiler is working, follow these steps:

1. Turn the chainsaw off and let it cool down.
2. Remove the bar cover.
3. Look at the oiler hole. If there is no oil coming out, the oiler is not working.
4. Clean the oiler hole and replace the oiler o-ring.
5. Reinstall the bar cover.

4. The bar is damaged

If the bar is damaged, it will not be able to hold the chain tight. To check if the bar is damaged, follow these steps:

1. Turn the chainsaw off and remove the spark plug.
2. Inspect the bar for any damage. If the bar is bent, cracked, or otherwise damaged, it will need to be replaced.
3. Reinstall the spark plug and start the chainsaw.

5. The chain is damaged

If the chain is damaged, it will not be able to stay tight on the bar. To check if the chain is damaged, follow these steps:

1. Turn the chainsaw off and remove the spark plug.
2. Inspect the chain for any damage. If the chain is broken, cracked, or otherwise damaged, it will need to be replaced.
3. Reinstall the spark plug and start the chainsaw.

How to Troubleshoot: Earthwise 16 Corded Chainsaw Tooless Tensioning Not Working

Symptoms

The chain is loose on the bar.
The chain is difficult to turn.
The chain jumps off the bar.

Causes

The chain is not properly adjusted.
The chain is worn out.
The bar is bent.
The chain brake is engaged.

Solutions

1. Adjust the chain tension. To do this, loosen the locknut on the bar and turn the tensioning screw clockwise until the chain is snug against the bar. Tighten the locknut.
2. Replace the chain. If the chain is worn out, it will need to be replaced. To do this, remove the old chain and install a new one.
3. Bend the bar straight. If the bar is bent, it will need to be straightened. To do this, use a vice to bend the bar back into shape.
4. Disengage the chain brake. If the chain brake is engaged, it will prevent the chain from turning. To disengage the chain brake, press the release button.

Prevention

To prevent your Earthwise 16 corded chainsaw from having tensioning problems, you can do the following:

Keep the chain properly adjusted.
Inspect the chain regularly for wear and tear.
Replace the chain as needed.
Avoid bending the bar.
Disengage the chain brake when not in use.

By following these tips, you can help keep your Earthwise 16 corded chainsaw running smoothly and safely.

Also Check: Earthwise 16 Corded Chainsaw Not Working

FAQs: Earthwise 16-inch Corded Chainsaw Tooless Tensioning Not Working

Why is my Earthwise chainsaw’s tooless tensioning not working?

There are a few possible reasons why your Earthwise chainsaw’s tooless tensioning system may not be working properly.

The chain is too tight. If the chain is too tight, it can bind up the sprockets and prevent the chain from moving freely. To check the chain tension, loosen the lock nut on the bar and slide the chain off. The chain should have about 1/8-inch of play when you pull it up with your fingers. If the chain is too tight, loosen the lock nut and slide the chain back on.
The chain is too loose. If the chain is too loose, it can come off the bar and cause injury. To check the chain tension, loosen the lock nut on the bar and slide the chain off. The chain should have about 1/8-inch of play when you pull it up with your fingers. If the chain is too loose, tighten the lock nut and slide the chain back on.
The chain is dirty. A dirty chain can cause the sprockets to bind up and prevent the chain from moving freely. To clean the chain, remove it from the bar and use a brush to scrub off any dirt or debris.
The bar is damaged. A damaged bar can cause the chain to bind up and prevent the chain from moving freely. If the bar is damaged, you will need to replace it.
The sprockets are damaged. Damaged sprockets can cause the chain to bind up and prevent the chain from moving freely. If the sprockets are damaged, you will need to replace them.

How do I fix my Earthwise chainsaw’s tooless tensioning system?

To fix your Earthwise chainsaw’s tooless tensioning system, you will need to identify the problem and take the appropriate steps to fix it.

If the chain is too tight, loosen the lock nut on the bar and slide the chain off. The chain should have about 1/8-inch of play when you pull it up with your fingers. If the chain is still too tight, loosen the lock nut a little more and try again.
If the chain is too loose, tighten the lock nut on the bar and slide the chain back on. The chain should have about 1/8-inch of play when you pull it up with your fingers. If the chain is still too loose, tighten the lock nut a little more and try again.
If the chain is dirty, remove it from the bar and use a brush to scrub off any dirt or debris.
If the bar is damaged, you will need to replace it.
If the sprockets are damaged, you will need to replace them.

What are the benefits of a tooless tensioning system?

There are a few benefits to a tooless tensioning system.

Convenience: A tooless tensioning system allows you to adjust the chain tension without having to use any tools. This can be a great convenience, especially if you are in the middle of a project and need to make an adjustment.
Speed: A tooless tensioning system can be adjusted quickly and easily. This can save you time, especially if you are making frequent adjustments.
Accuracy: A tooless tensioning system allows you to make accurate adjustments to the chain tension. This can help to ensure that your chain is properly tensioned and that your chainsaw is operating at peak performance.

What are the drawbacks of a tooless tensioning system?

There are a few drawbacks to a tooless tensioning system.

Complexity: A tooless tensioning system can be more complex than a traditional chain tensioning system. This can make it more difficult to troubleshoot if there is a problem.
Cost: A tooless tensioning system can be more expensive than a traditional chain tensioning system.
Durability: A tooless tensioning system may not be as durable as a traditional chain tensioning system. This can be a problem if you use your chainsaw in harsh conditions.

What are some tips for using a tooless tensioning system?

Here are a few tips for using a tooless tensioning system:

Always wear safety glasses when using a chainsaw.
Make sure the chainsaw is turned off and the chain is stopped before making any adjustments.
Use