Easy Kleen Pressure Washer Burner Not Working: [Quick Fixes]

If your Easy Kleen pressure washer burner isn’t working, you’re not alone. This is a common problem that can be frustrating and inconvenient. However, it’s usually easy to fix. In this guide, I’ll walk you through the steps to troubleshoot and resolve the issue so you can get your pressure washer up and running again.

I’ll start by explaining how the burner works and what could cause it to stop working. Then, I’ll provide you with a step-by-step guide to diagnosing the problem. Finally, I’ll give you some tips on how to prevent this issue from happening again in the future.

Most Common Reasons Easy Kleen Pressure Washer Burner Not Working

Most Common Reasons

1. No Gas

The most common reason for a pressure washer burner not working is that there is no gas. Make sure that the gas tank is full and that the gas valve is turned on.

2. Clogged Fuel Line

A clogged fuel line can also prevent the burner from working. Check the fuel line for any blockages and clean it out if necessary.

3. Bad Gas Valve

If the gas valve is not working properly, it can prevent the burner from getting gas. Check the gas valve for any damage or corrosion and replace it if necessary.

4. Bad Igniter

The igniter is responsible for igniting the gas in the burner. If the igniter is not working properly, the burner will not be able to start. Check the igniter for any damage or corrosion and replace it if necessary.

5. Bad Thermocouple

The thermocouple is a safety device that prevents the burner from operating if the temperature gets too high. If the thermocouple is not working properly, the burner will not be able to start. Check the thermocouple for any damage or corrosion and replace it if necessary.

How to Troubleshoot: Easy Kleen Pressure Washer Burner Not Working

Symptoms of a Pressure Washer Burner Not Working

There are a few different symptoms that can indicate that your Easy Kleen pressure washer burner is not working properly. These include:

The pressure washer won’t start or it starts but then shuts off immediately.

The pressure washer produces very little or no hot water.

The pressure washer makes a loud buzzing or humming noise.

The pressure washer smells like gas.

Causes of a Pressure Washer Burner Not Working

There are a number of different things that can cause a pressure washer burner to stop working. These include:

A dirty or clogged fuel filter.

A faulty fuel pump.

A faulty spark plug.

A bad regulator.

A blocked nozzle.

A loose or damaged hose.

A problem with the pressure washer’s electrical system.

How to Troubleshoot a Pressure Washer Burner Not Working

To troubleshoot a pressure washer burner that is not working, you will need to:

1. Inspect the fuel filter:
The fuel filter is located on the fuel line between the fuel tank and the burner. To inspect the fuel filter, remove it from the fuel line and visually inspect it for dirt, debris, or other blockages. If the fuel filter is dirty or clogged, replace it with a new one.

2. Check the fuel pump:
The fuel pump is located on the pressure washer’s engine. To check the fuel pump, turn on the pressure washer and listen for the fuel pump to prime. If you do not hear the fuel pump priming, the fuel pump may be faulty. You can test the fuel pump by disconnecting the fuel line from the burner and spraying some starter fluid into the fuel line. If the pressure washer starts up and runs, the fuel pump is probably faulty.3. Check the spark plug:
The spark plug is located in the burner. To check the spark plug, remove it from the burner and visually inspect it for damage. If the spark plug is damaged, replace it with a new one.

4. Check the regulator:
The regulator is located on the pressure washer’s engine. To check the regulator, turn on the pressure washer and listen for the regulator to click. If you do not hear the regulator clicking, the regulator may be faulty. You can test the regulator by disconnecting the pressure hose from the pressure washer and spraying some starter fluid into the pressure hose. If the pressure washer starts up and runs, the regulator is probably faulty.

5. Check the nozzle:
The nozzle is located on the end of the pressure washer’s wand. To check the nozzle, remove it from the wand and visually inspect it for damage. If the nozzle is damaged, replace it with a new one.

6. Check the hose:
The hose is located between the pressure washer and the nozzle. To check the hose, inspect it for leaks or damage. If the hose is damaged, replace it with a new one.

7. Check the electrical system:
The electrical system is made up of the pressure washer’s switch, wiring, and spark plug. To check the electrical system, turn on the pressure washer and look for any loose or damaged wires. If you find any loose or damaged wires, reconnect or repair them. You can also test the electrical system by using a multimeter to check the voltage at the spark plug. If the voltage at the spark plug is not within the specified range, the electrical system may be faulty.

How to Fix a Pressure Washer Burner Not Working

Once you have identified the cause of the problem, you can fix the pressure washer burner by following these steps:

1. Replace the fuel filter:
To replace the fuel filter, simply unscrew the old fuel filter and screw on the new one.

2. Replace the fuel pump:
To replace the fuel pump, remove the old fuel pump and install the new one. Be sure to tighten the fuel pump mounting bolts securely.3. Replace the spark plug:
To replace the spark plug, unscrew the old spark plug and screw on the new one. Be sure to tighten the spark plug securely.

4. Replace the regulator:
To replace the regulator, remove the old regulator and install the new one. Be sure to tighten the regulator mounting bolts securely.

5. Replace the nozzle:
To replace the nozzle, simply unscrew the old nozzle and screw on the new one.

6. Replace the hose:
To replace the hose, simply disconnect the old hose from the pressure washer and the nozzle and connect

Also Read: Electric Pressure Washer Soap Dispenser Not Working