Ex-Cell 2100 Psi Pressure Washer Soap Not Working [Solved]

Do you have an Ex-Cell 2100 PSI pressure washer that’s not dispensing soap If so, you’re not alone. This is a common problem that can be frustrating and inconvenient. But don’t worry, there’s a simple fix.

In this guide, I’ll walk you through the steps to troubleshoot and fix the problem of your Ex-Cell 2100 PSI pressure washer not dispensing soap. I’ll also provide some tips on how to prevent this problem from happening in the future.

So if you’re ready to get your pressure washer up and running again, let’s get started!

Reasons Why Ex-Cell 2100 Psi Pressure Washer Soap Not Working

Incorrect Soap Type

The Ex-Cell 2100 PSI pressure washer is designed to use detergent-based soaps. If you use a non-detergent soap, it will not foam properly and will not be effective at cleaning.

Incorrect Soap Concentration

The Ex-Cell 2100 PSI pressure washer requires a soap concentration of 1 to 2 ounces per gallon of water. If you use too much soap, it will not foam properly and will clog the spray nozzle. If you use too little soap, it will not be effective at cleaning.

Clogged Spray Nozzle

If the spray nozzle on the Ex-Cell 2100 PSI pressure washer is clogged, it will not be able to produce a fine mist of soap. This will prevent the soap from reaching the surface you are cleaning and will make it difficult to remove dirt and grime.

Low Pressure

If the pressure of the Ex-Cell 2100 PSI pressure washer is too low, it will not be able to produce a fine mist of soap. This will prevent the soap from reaching the surface you are cleaning and will make it difficult to remove dirt and grime.

Faulty Soap Injector

The Ex-Cell 2100 PSI pressure washer has a soap injector that mixes the soap with the water. If the soap injector is faulty, it will not be able to properly mix the soap and water. This will result in a soap solution that is too thick or too thin, which will not be effective at cleaning.

How to Troubleshoot: ex-cell 2100 psi pressure washer soap not working

Symptoms

There are a few different symptoms that you may experience if your ex-cell 2100 psi pressure washer soap is not working properly. These include:

The soap does not come out of the wand when you press the trigger.
The soap comes out of the wand in a weak stream.
The soap comes out of the wand in aerated bubbles.
The soap comes out of the wand in a solid stream.

Causes

There are a few different things that could cause your ex-cell 2100 psi pressure washer soap to not work properly. These include:

The soap dispenser is clogged:
If the soap dispenser is clogged, it will not be able to dispense the soap properly. This can be caused by a build-up of soap residue or debris.

The soap is too thick:
If the soap is too thick, it will not be able to flow through the soap dispenser properly. This can be caused by using a soap that is too concentrated or by adding too much soap to the dispenser.

The water pressure is too low:
If the water pressure is too low, it will not be able to push the soap through the soap dispenser properly. This can be caused by a problem with the water supply or by a problem with the pressure washer itself.

The soap wand is clogged:
If the soap wand is clogged, it will not be able to dispense the soap properly. This can be caused by a build-up of soap residue or debris.

Solutions

There are a few different things that you can do to troubleshoot a problem with your ex-cell 2100 psi pressure washer soap. These include:

Check the soap dispenser:
If the soap dispenser is clogged, you can try to clear it by using a small brush or by running a vinegar solution through it.

Thin the soap:
If the soap is too thick, you can thin it by adding a little bit of water to it.

Increase the water pressure:
If the water pressure is too low, you can try to increase it by turning on the water supply to the pressure washer or by adjusting the pressure regulator on the pressure washer.

Clean the soap wand:
If the soap wand is clogged, you can try to clear it by using a small brush or by running a vinegar solution through it.

If you have tried all of these solutions and your ex-cell 2100 psi pressure washer soap is still not working properly, you may need to contact a qualified technician for help.

Also Read: Exg 2300 Electric Pressure Washer Not Working

FAQs: Ex-Cell 2100 PSI Pressure Washer Soap Not Working

Why isn’t my Ex-Cell 2100 PSI pressure washer soap working?

There are a few possible reasons why your Ex-Cell 2100 PSI pressure washer soap may not be working. Here are a few things to check:

Is the soap reservoir full? The soap reservoir should be at least half full in order for the soap to flow properly.

Is the soap nozzle clogged? Check the soap nozzle to make sure that it is not clogged with soap or debris. If it is clogged, you can try to clean it with a toothpick or a needle.

Is the soap injector working properly? The soap injector is a small valve that allows the soap to flow from the reservoir to the wand. If the injector is not working properly, you may need to replace it.

Is the pressure washer turned on? Make sure that the pressure washer is turned on and that the soap injector is engaged.

How do I add soap to my Ex-Cell 2100 PSI pressure washer?

To add soap to your Ex-Cell 2100 PSI pressure washer, follow these steps:

1. Turn off the pressure washer and disconnect the wand from the gun.
2. Open the soap reservoir lid.
3. Add soap to the reservoir until it is at least half full.
4. Close the soap reservoir lid.
5. Reattach the wand to the gun.
6. Turn on the pressure washer and test the soap flow.

How do I change the soap nozzle on my Ex-Cell 2100 PSI pressure washer?

To change the soap nozzle on your Ex-Cell 2100 PSI pressure washer, follow these steps:

1. Turn off the pressure washer and disconnect the wand from the gun.
2. Remove the old soap nozzle by unscrewing it from the wand.
3. Insert the new soap nozzle into the wand and screw it on until it is tight.
4. Reattach the wand to the gun.
5. Turn on the pressure washer and test the soap flow.

How do I troubleshoot my Ex-Cell 2100 PSI pressure washer soap not working?

If your Ex-Cell 2100 PSI pressure washer soap is not working, here are a few things you can check:

Is the soap reservoir full? The soap reservoir should be at least half full in order for the soap to flow properly.

Is the soap nozzle clogged? Check the soap nozzle to make sure that it is not clogged with soap or debris. If it is clogged, you can try to clean it with a toothpick or a needle.

Is the soap injector working properly? The soap injector is a small valve that allows the soap to flow from the reservoir to the wand. If the injector is not working properly, you may need to replace it.

Is the pressure washer turned on? Make sure that the pressure washer is turned on and that the soap injector is engaged.

If you have checked all of these things and your Ex-Cell 2100 PSI pressure washer soap is still not working, you may need to contact a qualified technician for help.

Where can I buy replacement parts for my Ex-Cell 2100 PSI pressure washer?

You can buy replacement parts for your Ex-Cell 2100 PSI pressure washer from a variety of online retailers and hardware stores. Here are a few links to some of the most popular retailers:

[Amazon](https://www.amazon.com/s?k=ex-cell+2100+psi+pressure+washer+parts)
[Home Depot](https://www.homedepot.com/b/Tools-Hardware-Power-Washers-Parts-and-Accessories/Ex-Cell/N-5yc1vZc399z)
[Lowe’s](https://www.lowes.com/b/Tools-Hardware-Power-Washers-Parts-and-Accessories/Ex-Cell/N-5yc1vZc399z)