Gas Weed Eater Hedge Trimmer Won’T Start [Fixed]

There’s nothing more frustrating than a gas weed eater hedge trimmer that won’t start. You’re ready to tackle that overgrown hedge, but your trimmer is just sitting there, idling. You’ve tried everything you can think of, but it just won’t cooperate.

If you’re dealing with a gas weed eater hedge trimmer that won’t start, you’re not alone. This is a common problem, and there are a few simple things you can check to try to fix it. In this guide, I’ll walk you through the most common causes of this problem and how to troubleshoot them. So if you’re ready to get your trimmer up and running again, keep reading!

Reasons Why Gas Weed Eater Hedge Trimmer Won’T Start

Engine Won’t Crank

Out of fuel: The most common reason for a gas hedge trimmer not starting is that it is out of fuel. Check the fuel tank and make sure that it is full.

Bad spark plug: If the spark plug is bad, it will not be able to generate a spark, which is necessary to start the engine. Remove the spark plug and inspect it for damage. If the spark plug is fouled or damaged, replace it with a new one.

Clogged carburetor: If the carburetor is clogged, it will not be able to deliver fuel to the engine properly. Clean the carburetor according to the manufacturer’s instructions.

Bad fuel filter: If the fuel filter is clogged, it will restrict the flow of fuel to the engine. Replace the fuel filter with a new one.

Bad ignition switch: If the ignition switch is bad, it will not be able to send power to the spark plug. Replace the ignition switch with a new one.

Engine Cranks But Won’t Start

Low compression: If the engine has low compression, it will not be able to start. Check the compression and make sure that it is within the manufacturer’s specifications.

Bad valve timing: If the valve timing is off, it will cause the engine to misfire and not start. Adjust the valve timing according to the manufacturer’s instructions.

Bad spark plug wires: If the spark plug wires are damaged or corroded, they will not be able to deliver a spark to the spark plugs. Replace the spark plug wires with new ones.

Bad ignition coil: If the ignition coil is bad, it will not be able to generate a spark. Replace the ignition coil with a new one.

Engine Starts But Dies Immediately

Lean fuel mixture: If the fuel mixture is too lean, the engine will not have enough fuel to run properly. Adjust the carburetor to enrich the fuel mixture.

Clogged air filter: If the air filter is clogged, it will restrict the flow of air to the engine. Clean or replace the air filter.

Bad fuel pump: If the fuel pump is bad, it will not be able to deliver fuel to the engine properly. Replace the fuel pump with a new one.

Bad fuel injectors: If the fuel injectors are bad, they will not be able to deliver fuel to the engine properly. Clean or replace the fuel injectors.

How to Troubleshoot: Gas Weed Eater Hedge Trimmer Won’t Start

Your gas weed eater hedge trimmer is a valuable tool for keeping your yard looking its best. But what happens when it won’t start? This can be a frustrating problem, but it’s usually one that you can fix yourself.

In this blog post, we’ll walk you through the steps to troubleshoot a gas weed eater hedge trimmer that won’t start. We’ll cover everything from checking the fuel and spark plug to diagnosing more serious problems.

Step 1: Check the Fuel

The first thing you should do when your weed eater hedge trimmer won’t start is check the fuel. Make sure that there is enough fuel in the tank and that the fuel is fresh. If the fuel is old, it can cause problems with starting.

To check the fuel, remove the fuel cap and look inside the tank. If the fuel is low, fill the tank up with fresh fuel. If the fuel is old, drain the tank and refill it with fresh fuel.

Step 2: Check the Spark Plug

Once you’ve checked the fuel, the next thing you should do is check the spark plug. The spark plug is responsible for igniting the fuel in the engine. If the spark plug is dirty or damaged, it can prevent the engine from starting.

To check the spark plug, remove it from the engine using a spark plug wrench. Inspect the spark plug for signs of damage. If the spark plug is dirty, clean it with a wire brush. If the spark plug is damaged, replace it with a new one.

Step 3: Check the Air Filter

The air filter helps to keep dirt and debris out of the engine. If the air filter is dirty, it can restrict airflow to the engine and cause problems with starting.

To check the air filter, remove it from the engine. Inspect the air filter for signs of dirt and debris. If the air filter is dirty, clean it with a mild detergent and water. If the air filter is damaged, replace it with a new one.

Step 4: Check the Carburetor

The carburetor is responsible for mixing the fuel and air in the correct proportions. If the carburetor is not adjusted properly, it can cause problems with starting.

To check the carburetor, you will need to remove the carburetor from the engine. Once the carburetor is removed, you can inspect it for signs of damage. If the carburetor is damaged, you will need to have it repaired or replaced.

You can also adjust the carburetor to ensure that it is mixing the fuel and air in the correct proportions. If you are not familiar with carburetors, it is best to have a professional adjust the carburetor for you.

Step 5: Check the Ignition System

The ignition system is responsible for providing the spark that ignites the fuel in the engine. If the ignition system is not working properly, it can prevent the engine from starting.

To check the ignition system, you will need to use a spark tester. A spark tester is a tool that allows you to check the spark at the spark plug.

To use a spark tester, connect the spark tester to the spark plug wire. Crank the engine over and watch the spark tester. If the spark tester does not show a spark, the ignition system is not working properly.

If the ignition system is not working properly, you will need to have it repaired or replaced.

Step 6: Check the Engine

If you have checked all of the above and your weed eater hedge trimmer still won’t start, it is possible that there is a problem with the engine itself.

To check the engine, you will need to remove the spark plug and look inside the cylinder. If the cylinder is filled with oil, it is possible that the engine is seized. If the engine is seized, you will need to have it repaired or replaced.

Conclusion

Troubleshooting a gas weed eater hedge trimmer that won’t start can be a frustrating experience, but it is usually a problem that you can fix yourself. By following the steps in this blog post, you can quickly and easily get your weed eater hedge trimmer back up and running.

Also Read: Hedge Trimmer Attachment Not Working

FAQs: Gas Weed Eater Hedge Trimmer Won’t Start

Why won’t my gas weed eater hedge trimmer start?

There are a few possible reasons why your gas weed eater hedge trimmer won’t start. Here are some of the most common causes:

The engine is not getting fuel: Make sure that the fuel tank is full and that the fuel line is not clogged.

The spark plug is not firing: Check the spark plug for damage and clean or replace it if necessary.

The air filter is dirty: Clean or replace the air filter if it is dirty.

The carburetor is out of adjustment: Have the carburetor adjusted by a qualified technician.

The engine is flooded: If the engine is flooded, turn the choke off and wait a few minutes before trying to start it again.

What should I do if my gas weed eater hedge trimmer won’t start?

If your gas weed eater hedge trimmer won’t start, here are some steps you can take to troubleshoot the problem:

1. Check the fuel tank: Make sure that the fuel tank is full and that the fuel line is not clogged.
2. Check the spark plug: Remove the spark plug and check for damage. If the spark plug is damaged, clean or replace it.
3. Check the air filter: Remove the air filter and check for dirt or debris. If the air filter is dirty, clean it or replace it.
4. Check the carburetor: If the carburetor is out of adjustment, have it adjusted by a qualified technician.
5. Flooded engine: If the engine is flooded, turn the choke off and wait a few minutes before trying to start it again.

How do I prevent my gas weed eater hedge trimmer from not starting?

There are a few things you can do to prevent your gas weed eater hedge trimmer from not starting:

Keep the fuel tank full: A full fuel tank will help to prevent the engine from flooding.

Clean the spark plug regularly: A dirty spark plug can cause the engine to misfire and not start.

Replace the air filter regularly: A dirty air filter can restrict airflow to the engine and cause it to not start.

Adjust the carburetor regularly: A carburetor that is out of adjustment can cause the engine to run poorly and not start.

Flooded engine: If the engine is flooded, turn the choke off and wait a few minutes before trying to start it again.

What are the signs that my gas weed eater hedge trimmer needs maintenance?

There are a few signs that your gas weed eater hedge trimmer needs maintenance:

The engine is running rough or not starting.
The engine is smoking or making strange noises.
The trimmer is not cutting grass as well as it used to.
The trimmer is leaking gas or oil.
The trimmer is overheating.

If you notice any of these signs, it is important to have your trimmer serviced by a qualified technician.

How often should I have my gas weed eater hedge trimmer serviced?

The frequency with which you should have your gas weed eater hedge trimmer serviced depends on how often you use it. If you use your trimmer regularly, you should have it serviced at least once a year. If you only use your trimmer occasionally, you may be able to get away with servicing it every two or three years.

When you have your trimmer serviced, the technician will check the engine, spark plug, air filter, carburetor, and other components to make sure that they are working properly. They will also clean and lubricate the trimmer and replace any worn or damaged parts.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *