Hozelock Pressure Washer Not Working [Easy Troubleshooting]

Your Hozelock pressure washer is not working, and you’re frustrated. You need to get the job done, and this is just one more thing in your way. But don’t worry, you’re not alone. Pressure washers are complex machines, and even the most experienced homeowners can run into problems.

In this guide, I’ll walk you through the most common causes of a and how to fix them. I’ll also provide some tips on how to prevent future problems. By the end of this guide, you’ll be able to get your pressure washer up and running again in no time.

Reasons Why Hozelock Pressure Washer Not Working

No Water Flow

Blocked inlet filter:
The inlet filter is located at the end of the hose that connects to the water source. If it is clogged, water will not be able to flow into the pressure washer. To clean the filter, remove it from the hose and rinse it under running water.

Clogged pump:
The pump is located inside the pressure washer and is responsible for pumping water from the inlet to the outlet. If the pump is clogged, water will not be able to flow through it. To clean the pump, remove the inlet and outlet hoses and disconnect the power cord. Then, use a small brush to clean out any debris that is blocking the pump.

Damaged pump:
If the pump is damaged, it will not be able to pump water. To determine if the pump is damaged, you can try running the pressure washer without any water connected to the inlet. If the pump makes a loud noise or does not start, it is likely damaged. You will need to replace the pump.

Low Pressure

Low water pressure at the source:
If the water pressure at the source is too low, the pressure washer will not be able to generate high pressure. To check the water pressure at the source, use a pressure gauge to measure the pressure at the faucet. If the pressure is below 40 psi, the pressure washer will not work properly.

Clogged nozzle:
The nozzle is located at the end of the wand and is responsible for directing the water stream. If the nozzle is clogged, the water stream will be weak. To clean the nozzle, remove it from the wand and soak it in a vinegar and water solution for a few minutes. Then, rinse the nozzle under running water and reattach it to the wand.

Damaged pump:
If the pump is damaged, it will not be able to generate high pressure. To determine if the pump is damaged, you can try running the pressure washer without any water connected to the inlet. If the pump makes a loud noise or does not start, it is likely damaged. You will need to replace the pump.

Pressure Washer Won’t Start

Power cord not plugged in:
Make sure that the power cord is plugged into an outlet and that the outlet is turned on.

Blown fuse:
If the pressure washer has a built-in fuse, it may have blown. To check the fuse, look for a small, round object in the electrical compartment. If the fuse is blackened or broken, it needs to be replaced.

Damaged switch:
The switch on the pressure washer is responsible for turning the power on and off. If the switch is damaged, the pressure washer will not start. You will need to replace the switch.

Damaged motor:
If the motor is damaged, the pressure washer will not start. You will need to replace the motor.

How to Troubleshoot: Hozelock Pressure Washer Not Working

Your Hozelock pressure washer is a powerful tool that can make quick work of cleaning your home, car, or yard. But what happens when it stops working? Don’t panic! There are a few simple troubleshooting steps you can take to get your pressure washer up and running again.

Troubleshooting Steps

1. Check the power supply:
Make sure that the pressure washer is plugged in and turned on. If it is plugged in and turned on, but still not working, check the circuit breaker to make sure that it is not tripped.

2. Check the water supply:
Make sure that the water hose is connected to the pressure washer and to a water source. If the water hose is not connected properly, the pressure washer will not work.3. Check the pressure washer’s pump:
The pump is the heart of the pressure washer. If the pump is not working properly, the pressure washer will not generate any pressure. To check the pump, turn on the pressure washer and listen for the sound of the pump running. If you do not hear the pump running, the pump may be faulty.

4. Check the pressure washer’s hose:
The pressure washer hose can become kinked or damaged, which can prevent the pressure washer from generating pressure. To check the hose, inspect it for kinks or damage. If you find any kinks or damage, replace the hose.

5. Check the pressure washer’s nozzle:
The nozzle is the part of the pressure washer that directs the water stream. If the nozzle is clogged, the pressure washer will not generate any pressure. To check the nozzle, remove it from the pressure washer and clean it with a wire brush.

Additional Tips

If you are not comfortable troubleshooting your pressure washer, you can always take it to a qualified technician.
Make sure to read the owner’s manual for your pressure washer before you start troubleshooting. The manual will contain specific instructions for troubleshooting your particular model of pressure washer.
Keep your pressure washer clean and well-maintained. This will help to prevent problems from occurring in the first place.

Conclusion

By following these troubleshooting steps, you can usually get your Hozelock pressure washer up and running again in no time. If you are unable to troubleshoot the problem yourself, you can always take your pressure washer to a qualified technician.

Also Read: Husky 1750 Psi Pressure Washer Not Working

FAQs: Hozelock Pressure Washer Not Working

Why is my Hozelock pressure washer not working?

There are a few possible reasons why your Hozelock pressure washer might not be working. Here are some of the most common causes:

The water supply is turned off: Make sure that the water supply to your pressure washer is turned on and that there is no kink in the hose.

The pressure washer is not plugged in: Check to make sure that the pressure washer is plugged into an outlet and that the outlet is working.

The pressure washer is not primed: Priming the pressure washer ensures that there is enough water in the pump to create pressure. To prime the pressure washer, turn on the water supply and pull the trigger on the gun until water comes out.

The pressure washer is clogged: The pressure washer nozzle or filter may be clogged, preventing water from flowing through the pump. To clean the nozzle, remove it from the gun and soak it in a vinegar and water solution. To clean the filter, remove it from the pump and rinse it with water.

The pressure washer pump is damaged: If the pressure washer pump is damaged, it will not be able to generate pressure. If you suspect that the pump is damaged, you should take the pressure washer to a qualified repair technician.

How do I prime my Hozelock pressure washer?

To prime your Hozelock pressure washer, follow these steps:

1. Turn on the water supply to the pressure washer.
2. Pull the trigger on the gun until water comes out.
3. Continue to pull the trigger until the pressure washer builds up pressure.
4. Once the pressure washer is primed, you can release the trigger and start using it.

How do I clean the nozzle on my Hozelock pressure washer?

To clean the nozzle on your Hozelock pressure washer, follow these steps:

1. Turn off the water supply to the pressure washer.
2. Remove the nozzle from the gun.
3. Soak the nozzle in a vinegar and water solution for several minutes.
4. Rinse the nozzle with water.
5. Reattach the nozzle to the gun.

How do I clean the filter on my Hozelock pressure washer?

To clean the filter on your Hozelock pressure washer, follow these steps:

1. Turn off the water supply to the pressure washer.
2. Remove the filter from the pump.
3. Rinse the filter with water.
4. Dry the filter with a towel.
5. Reattach the filter to the pump.

What should I do if my Hozelock pressure washer is still not working?

If your Hozelock pressure washer is still not working after you have tried the troubleshooting steps above, you should take the pressure washer to a qualified repair technician. The technician will be able to diagnose the problem and repair the pressure washer so that it is working properly again.