Husqvarna Chainsaw 455 Rancher Bar Oiler Not Working: [Proven Fixes!]

As a chainsaw owner, there’s nothing more frustrating than having your bar oiler stop working. Not only does it make it difficult to keep your chain sharp and running smoothly, but it can also be dangerous. A dull chain is more likely to kickback, which can cause serious injury.

If your Husqvarna 455 Rancher bar oiler isn’t working, don’t despair. There are a few simple troubleshooting steps you can take to diagnose and resolve the problem. In this guide, I’ll walk you through the process, so you can get your chainsaw back up and running in no time.

Most Common Reasons Of Husqvarna Chainsaw 455 Rancher Bar Oiler Not Working

Most Common Reasons Of Husqvarna Chainsaw 455 Rancher Bar Oiler Not Working

1. Oiler Hose Is Clogged

The oiler hose can become clogged with sawdust or other debris, preventing oil from reaching the bar and chain. To clean the oiler hose, remove the hose from the bar and chain and blow it out with compressed air.

2. Oiler Pump Is Not Working

The oiler pump can fail due to a number of reasons, including a broken spring, a clogged oil filter, or a faulty oiler diaphragm. If the oiler pump is not working, you will need to replace it.

3. Oiler Level Is Low

If the oil level in the chainsaw is low, the oiler will not be able to pump enough oil to the bar and chain. To check the oil level, remove the oil cap and look at the oil level indicator. If the oil level is low, add oil to the chainsaw until the indicator reaches the full mark.

4. Oiler Switch Is Off

The oiler switch can be turned off accidentally, preventing oil from being pumped to the bar and chain. To check the oiler switch, make sure that it is turned on.

5. Bar and Chain Are Too Worn

If the bar and chain are too worn, they will not be able to create a proper oil mist, which can prevent oil from reaching the bar and chain. To check the condition of the bar and chain, look for signs of wear, such as deep scratches or gouges. If the bar and chain are too worn, you will need to replace them.

How to Troubleshoot: Husqvarna Chainsaw 455 Rancher Bar Oiler Not Working

Symptoms

There are a few symptoms that you may notice if the bar oiler on your Husqvarna Chainsaw 455 Rancher is not working properly. These include:

The chain is not being lubricated properly, which can lead to overheating and damage.
The bar oil level is low or empty.
The bar oiler is not pumping oil to the bar.
The bar oiler is clogged.

Troubleshooting

If you are experiencing any of the symptoms listed above, you can troubleshoot the problem by following these steps:

1. Check the bar oil level. If the bar oil level is low or empty, fill the reservoir with fresh bar oil.
2. Check the bar oiler pump. To do this, start the chainsaw and let it run for a few minutes. Then, look at the bar oiler pump. If the pump is not pumping oil, you will need to replace it.
3. Check the bar oiler hose. The bar oiler hose is a small hose that connects the bar oiler pump to the bar. If the hose is kinked or damaged, it will prevent oil from flowing to the bar. To check the hose, look for any kinks or damage. If you find any, replace the hose.
4. Clean the bar oiler screen. The bar oiler screen is a small screen that prevents dirt and debris from entering the bar oiler pump. If the screen is clogged, it will prevent oil from flowing to the bar. To clean the screen, remove it from the bar oiler pump and rinse it with warm water.

Prevention

You can prevent problems with the bar oiler on your Husqvarna Chainsaw 455 Rancher by following these tips:

Keep the bar oil level full.
Inspect the bar oiler pump regularly for damage.
Clean the bar oiler screen regularly.

By following these tips, you can help to ensure that your Husqvarna Chainsaw 455 Rancher bar oiler is working properly and that your chainsaw is properly lubricated.

Also Check: Husqvarna Chainsaw 455 Rancher Chain Oiler Not Working

FAQs: Husqvarna Chainsaw 455 Rancher Bar Oiler Not Working

Why is my Husqvarna chainsaw 455 rancher bar oiler not working?

There are a few possible reasons why your Husqvarna chainsaw 455 rancher bar oiler may not be working.

The oiler may be clogged. Check the oiler to make sure that it is not clogged with sawdust or other debris. If it is clogged, you can clean it out with a small brush or needle.
The oiler may not be getting enough oil. Make sure that the oil tank is full and that the oil line is not kinked or blocked.
The oiler may be turned off. Check the oiler to make sure that it is turned on.
The oiler may be defective. If you have checked all of the above and the oiler is still not working, it may be defective and need to be replaced.

How do I fix a clogged Husqvarna chainsaw 455 rancher bar oiler?

To fix a clogged Husqvarna chainsaw 455 rancher bar oiler, you can follow these steps:

1. Remove the oiler cover.
2. Use a small brush or needle to clean out the oiler.
3. Reattach the oiler cover.

How do I make sure my Husqvarna chainsaw 455 rancher bar oiler is getting enough oil?

To make sure your Husqvarna chainsaw 455 rancher bar oiler is getting enough oil, you can follow these steps:

1. Check the oil tank regularly to make sure that it is full.
2. Make sure that the oil line is not kinked or blocked.
3. Run the chainsaw for a few minutes and check to see if oil is coming out of the bar oiler.

How do I turn on the Husqvarna chainsaw 455 rancher bar oiler?

To turn on the Husqvarna chainsaw 455 rancher bar oiler, you can follow these steps:

1. Locate the oiler switch.
2. Flip the switch to the On position.

What should I do if my Husqvarna chainsaw 455 rancher bar oiler is defective?

If your Husqvarna chainsaw 455 rancher bar oiler is defective, you can contact Husqvarna customer service for a replacement. You can also find replacement parts for your chainsaw at your local Husqvarna dealer.