Husqvarna Chainsaw 455 Rancher Oiler Not Working: [Proven Ways To Fix]

As a chainsaw repair professional, I have seen firsthand the frustration and inconvenience that can be caused by a . This is a common problem that can be easily diagnosed and resolved, but it is important to do so quickly in order to restore functionality to the tool. In this troubleshooting guide, I will walk you through the steps necessary to identify and fix the issue so that you can get back to using your chainsaw as soon as possible.

Most Common Reasons Of Husqvarna Chainsaw 455 Rancher Oiler Not Working

Most Common Reasons Of Husqvarna Chainsaw 455 Rancher Oiler Not Working

1. Oiler Hose Clogged

The most common reason for a chainsaw 455 Rancher oljer not working is a clogged oiler hose. This can be caused by dirt, sawdust, or other debris getting into the hose and blocking the flow of oil. To fix this, you will need to remove the oiler hose from the chainsaw and clean it out. You can do this by using a small brush or pipe cleaner to loosen the debris, and then rinse the hose with warm water.

2. Oiler Tube Kinked

Another common cause of a chainsaw 455 Rancher oljer not working is a kinked oiler tube. This can happen if the tube is bent or damaged, which prevents the oil from flowing properly. To fix this, you will need to inspect the oiler tube for any kinks or damage. If you find any, you will need to replace the tube.

3. Oiler Pump Not Working

The oiler pump is responsible for pumping oil from the reservoir to the chain. If the pump is not working properly, it will not be able to deliver oil to the chain, which can lead to damage. To check if the oiler pump is working, you can listen for the pump to run when you start the chainsaw. If you do not hear the pump running, you will need to replace the pump.

4. Oil Level Low

If the oil level in the reservoir is too low, the oiler will not be able to deliver oil to the chain. To check the oil level, you will need to remove the oil cap and look at the oil level. If the oil level is low, you will need to add oil to the reservoir.

5. Oil Filter Clogged

The oil filter is located in the oil reservoir and helps to keep the oil clean. If the oil filter is clogged, it will not be able to filter the oil properly, which can lead to damage to the chainsaw. To check the oil filter, you will need to remove it from the oil reservoir and inspect it for any debris. If the oil filter is clogged, you will need to replace it.

How to Troubleshoot: Husqvarna Chainsaw 455 Rancher Oiler Not Working

Symptoms

If your Husqvarna chainsaw 455 Rancher oiler is not working, there are a few symptoms you can look for:

The chainsaw is running hot, even when it is not under load.
The chain is smoking or sparking.
The chain is not cutting through wood as easily as it used to.
The bar and chain are becoming excessively dirty.
The oil level in the oil tank is low.

Causes

There are a number of possible causes for a Husqvarna chainsaw 455 Rancher oiler not working, including:

The oiler is clogged.
The oiler is not getting enough oil.
The oil pump is not working properly.
The oil filter is clogged.
The oil line is clogged.

Troubleshooting

To troubleshoot a Husqvarna chainsaw 455 Rancher oiler not working, you will need to:

1. Check the oil level in the oil tank. If the oil level is low, add oil to the tank.
2. Check the oiler for clogs. Remove the oiler cover and look for any debris or blockages. Clean the oiler as necessary.
3. Check the oil pump. Remove the oil pump and check for damage or wear. Replace the oil pump if necessary.
4. Check the oil filter. Remove the oil filter and inspect it for damage or clogging. Replace the oil filter if necessary.
5. Check the oil line. Inspect the oil line for damage or kinks. Repair or replace the oil line if necessary.

Prevention

To prevent your Husqvarna chainsaw 455 Rancher oiler from not working, you can:

Keep the oil level in the oil tank full.
Clean the oiler regularly.
Replace the oil pump and oil filter regularly.
Inspect the oil line regularly for damage or kinks.

Conclusion

If you follow these tips, you can help prevent your Husqvarna chainsaw 455 Rancher oiler from not working. However, if your oiler does not work after troubleshooting, you should take your chainsaw to a qualified service center for repairs.

Also Check: Husqvarna Chainsaw 55 Chain Brake Not Working

FAQs: Husqvarna Chainsaw 455 Rancher Oiler Not Working

Why is my Husqvarna Chainsaw 455 Rancher oiler not working?

There are a few possible reasons why your Husqvarna Chainsaw 455 Rancher oiler may not be working. Here are some of the most common causes:

The oiler is not turned on. Make sure that the oiler switch is in the On position.
The oiler is clogged. The oiler can become clogged with dirt or debris, which can prevent it from working properly. To clean the oiler, remove the oiler cover and use a small brush to clean out any debris.
The oiler is not getting enough oil. The oiler may not be getting enough oil if the oil level is low. Check the oil level and add oil if necessary.
The oiler is not working properly. If the oiler is not working properly, it may need to be replaced.

How do I fix my Husqvarna Chainsaw 455 Rancher oiler?

To fix your Husqvarna Chainsaw 455 Rancher oiler, you will need to determine the cause of the problem. Once you have determined the cause, you can take the necessary steps to fix it.

If the oiler is not turned on, turn it on.
If the oiler is clogged, clean it out.
If the oiler is not getting enough oil, add oil.
If the oiler is not working properly, replace it.

What are the symptoms of a Husqvarna Chainsaw 455 Rancher oiler that is not working?

There are a few symptoms that may indicate that your Husqvarna Chainsaw 455 Rancher oiler is not working properly. These include:

The chainsaw is running hot. This is because the engine is not getting enough oil to cool it down.
The chainsaw is smoking. This is because the engine is burning oil.
The chainsaw is making a knocking noise. This is because the engine is not getting enough oil to lubricate it.
The chainsaw is losing power. This is because the engine is not getting enough oil to run properly.

How often should I oil my Husqvarna Chainsaw 455 Rancher?

You should oil your Husqvarna Chainsaw 455 Rancher every time you use it. You should also oil it if the chainsaw has been sitting for a long period of time.

What type of oil should I use for my Husqvarna Chainsaw 455 Rancher?

You should use a high-quality, 2-cycle oil for your Husqvarna Chainsaw 455 Rancher. You can find 2-cycle oil at most hardware stores.