Husqvarna Chainsaw Bar Oiler Not Working: [You Should Try This]

As a chainsaw owner, there’s nothing more frustrating than when your bar oiler stops working. Not only does it make it difficult to keep your chainsaw sharp and running smoothly, but it can also be dangerous. If the bar oiler isn’t working properly, your chain can overheat and become damaged.

In this guide, I’ll walk you through the steps to troubleshoot a Husqvarna chainsaw bar oiler that’s not working. I’ll cover everything from simple checks to more complex repairs, so you can get your chainsaw back up and running in no time.

By the end of this guide, you’ll have the knowledge and skills you need to diagnose and resolve any bar oiler problem. So if your chainsaw is giving you trouble, don’t despair – just follow these steps and you’ll be back to cutting wood in no time.

Most Common Reasons Of Husqvarna Chainsaw Bar Oiler Not Working

Most Common Reasons Of Husqvarna Chainsaw Bar Oiler Not Working

1. Oiler Hose Is Clogged

The most common reason for a Husqvarna chainsaw bar oiler not working is a clogged oiler hose. This can be caused by dirt, sawdust, or other debris getting into the hose and blocking the flow of oil. To fix this problem, you will need to remove the oiler hose from the chainsaw and clean it thoroughly.

2. Oiler Pump Is Damaged

Another common reason for a Husqvarna chainsaw bar oiler not working is a damaged oiler pump. The oiler pump is responsible for pumping oil from the reservoir to the bar and chain. If the pump is damaged, it will not be able to properly pump oil to the bar and chain, which can lead to the chain overheating and becoming damaged. To fix this problem, you will need to replace the oiler pump.

3. Oiler Reservoir Is Empty

A third common reason for a Husqvarna chainsaw bar oiler not working is an empty oiler reservoir. If the oiler reservoir is empty, the oiler will not be able to pump any oil to the bar and chain. To fix this problem, you will need to add oil to the oiler reservoir.

4. Oiler O-Ring Is Damaged

A fourth common reason for a Husqvarna chainsaw bar oiler not working is a damaged o-ring. The o-ring is a small rubber ring that seals the oiler pump to the oiler reservoir. If the o-ring is damaged, it will allow oil to leak out of the oiler pump, which can lead to the bar and chain becoming dry and damaged. To fix this problem, you will need to replace the o-ring.

5. Bar Oil Is Too Thick

A fifth common reason for a Husqvarna chainsaw bar oiler not working is using bar oil that is too thick. Thick bar oil can clog the oiler hose and prevent the oil from flowing to the bar and chain. To fix this problem, you will need to use bar oil that is the correct viscosity for your chainsaw.

6. Bar Oil Is Too Thin

A sixth common reason for a Husqvarna chainsaw bar oiler not working is using bar oil that is too thin. Thin bar oil can evaporate too quickly and not provide enough lubrication to the bar and chain. To fix this problem, you will need to use bar oil that is the correct viscosity for your chainsaw.

How to Troubleshoot: Husqvarna Chainsaw Bar Oiler Not Working

Symptoms of a Husqvarna Chainsaw Bar Oiler Not Working

There are a few symptoms that can indicate that your Husqvarna chainsaw bar oiler is not working properly. These include:

The bar oil reservoir is empty or low.
The bar oil is not flowing to the bar and chain.
The bar oil is leaking from the chainsaw.
The bar oil is not the correct type or viscosity.

Troubleshooting a Husqvarna Chainsaw Bar Oiler

If you are experiencing any of the symptoms listed above, you can try troubleshooting the bar oiler yourself. Here are a few steps to follow:

1. Check the bar oil reservoir. Make sure that the reservoir is full of oil. If it is empty or low, fill it up with the correct type and viscosity of oil.
2. Check the oil line. Make sure that the oil line is not kinked or blocked. If it is, straighten it out or clear the blockage.
3. Check the oil pump. The oil pump is responsible for sending oil to the bar and chain. If the pump is not working properly, it will not be able to deliver oil to the bar and chain. To check the oil pump, start the chainsaw and listen for the sound of the pump. You should be able to hear a faint whirring sound. If you do not hear any sound, the pump may be defective and will need to be replaced.
4. Check the oil filter. The oil filter helps to keep dirt and debris out of the oil system. If the filter is clogged, it will restrict the flow of oil to the bar and chain. To check the oil filter, remove it from the chainsaw and inspect it for damage. If the filter is clogged, replace it with a new one.

Preventing Husqvarna Chainsaw Bar Oiler Problems

You can help prevent Husqvarna chainsaw bar oiler problems by following these tips:

Keep the bar oil reservoir full.
Use the correct type and viscosity of oil.
Inspect the oil line regularly for kinks or blockages.
Clean the oil pump regularly.
Replace the oil filter regularly.

By following these tips, you can help to keep your Husqvarna chainsaw running smoothly and efficiently.

Also Check: Husqvarna Chainsaw Chain Oiler Not Working

FAQs: Husqvarna Chainsaw Bar Oiler Not Working

Why isn’t my Husqvarna chainsaw bar oiler working?

There are a few possible reasons why your Husqvarna chainsaw bar oiler might not be working. Here are some of the most common causes:

The oiler is not turned on. Make sure that the oiler switch is in the On position.
The oiler is clogged. The oiler can become clogged with sawdust or other debris, which can prevent the oil from flowing to the bar and chain. To clean the oiler, remove the oiler cover and clean the inside of the oiler with a small brush.
The oiler hose is kinked or damaged. The oiler hose can become kinked or damaged, which can prevent the oil from flowing to the bar and chain. To check the oiler hose, look for kinks or damage. If you find any, replace the hose.
The oil level is low. The oil level in the oil reservoir can become low, which can prevent the oil from flowing to the bar and chain. To check the oil level, remove the oiler cover and look at the oil level. If the oil level is low, add oil to the reservoir.
The oil pump is not working. The oil pump can malfunction, which can prevent the oil from flowing to the bar and chain. If you think the oil pump is not working, take your chainsaw to a Husqvarna dealer for service.

How do I fix a Husqvarna chainsaw bar oiler that’s not working?

To fix a Husqvarna chainsaw bar oiler that’s not working, you will need to identify the cause of the problem and then take the appropriate steps to fix it. Here are the steps to fix a Husqvarna chainsaw bar oiler that’s not working:

1. Check the oiler switch. Make sure that the oiler switch is in the On position.
2. Clean the oiler. Remove the oiler cover and clean the inside of the oiler with a small brush.
3. Check the oiler hose. Look for kinks or damage to the oiler hose. If you find any, replace the hose.
4. Check the oil level. Make sure that the oil level in the oil reservoir is adequate. If the oil level is low, add oil to the reservoir.
5. Take your chainsaw to a Husqvarna dealer for service. If you think the oil pump is not working, take your chainsaw to a Husqvarna dealer for service.

What are the symptoms of a Husqvarna chainsaw bar oiler that’s not working?

There are a few symptoms that you can look for to indicate that your Husqvarna chainsaw bar oiler is not working properly. These symptoms include:

The chain is not being lubricated properly.
The chain is getting hot.
The chain is smoking.
The chain is making a strange noise.
The chain is wearing out quickly.

If you notice any of these symptoms, it is important to take your chainsaw to a Husqvarna dealer for service.

How often should I oil the bar and chain on my Husqvarna chainsaw?

The frequency with which you should oil the bar and chain on your Husqvarna chainsaw will depend on the type of work you are doing and the conditions you are working in. However, as a general rule, you should oil the bar and chain every 10-15 minutes of use.

What type of oil should I use for my Husqvarna chainsaw bar and chain?

You should use a high-quality bar and chain oil for your Husqvarna chainsaw. Bar and chain oil is designed to lubricate the bar and chain and prevent them from overheating and wearing out prematurely.

Here are a few tips for choosing the right bar and chain oil for your Husqvarna chainsaw:

Choose an oil that is specifically designed for chainsaws. Bar and chain oil is formulated to withstand the high temperatures and pressures generated by a chainsaw.
Choose an oil that is compatible with the type of bar and chain you are using. Some bar and chain oils are not compatible with certain types of bars and chains.
Choose an oil that has a high viscosity. A high-viscosity oil will provide better lubrication and protection for your bar and chain.

Here are a few popular brands of bar and chain oil:

Husqvarna