Husqvarna Chainsaw Chain Oiler Not Working: [Try This Proven Fixes]

As a chainsaw owner, there’s nothing more frustrating than having your chain oiler stop working. Not only does it make it difficult to keep your chain sharp and running smoothly, but it can also be dangerous. A dull chain is more likely to kickback, which can cause serious injury.

If your Husqvarna chainsaw chain oiler isn’t working, don’t despair. There are a few simple troubleshooting steps you can take to diagnose and resolve the problem. In this guide, I’ll walk you through the process, so you can get your chainsaw back up and running in no time.

Most Common Reasons Of Husqvarna Chainsaw Chain Oiler Not Working

1. Insufficient Oil in the Tank

The most common reason for a chainsaw chain oiler not working is that there is not enough oil in the tank. To check the oil level, remove the oil cap and look inside the tank. The oil level should be between the full and add marks. If the oil level is low, add more oil to the tank.

2. Clogged Oil Hose

Another common cause of a chainsaw chain oiler not working is a clogged oil hose. The oil hose is a small tube that connects the oil tank to the chain bar. If the oil hose is clogged, oil will not be able to flow to the chain bar and the chain will not be lubricated. To check the oil hose, remove the oil cap and look inside the tank. You should be able to see the oil hose running from the tank to the chain bar. If the oil hose is clogged, you will need to clean it or replace it.

3. Kinked Oil Hose

A kinked oil hose can also prevent oil from flowing to the chain bar. If the oil hose is kinked, it will restrict the flow of oil and the chain will not be lubricated. To check the oil hose, look for any kinks or bends. If you find a kink, you will need to straighten it out or replace the hose.

4. Faulty Oil Pump

The oil pump is responsible for pumping oil from the tank to the chain bar. If the oil pump is faulty, it will not be able to pump oil to the chain bar and the chain will not be lubricated. To check the oil pump, remove the oil cap and look inside the tank. You should be able to see the oil pump inside the tank. If the oil pump is not moving, it is faulty and will need to be replaced.

5. Blocked Oil Passages

The oil passages are small channels that allow oil to flow from the oil pump to the chain bar. If the oil passages are blocked, oil will not be able to flow to the chain bar and the chain will not be lubricated. To check the oil passages, remove the oil cap and look inside the tank. You should be able to see the oil passages running from the oil pump to the chain bar. If the oil passages are blocked, you will need to clean them or replace them.

How to Troubleshoot: Husqvarna Chainsaw Chain Oiler Not Working

Symptoms of a Chainsaw Chain Oiler Not Working

There are a few different symptoms that you may notice if your chainsaw chain oiler is not working properly. These include:

The chain is not being lubricated properly, which can lead to overheating and damage to the chain.
The chain is making a loud squealing noise, which is caused by the chain rubbing against the bar without lubrication.
The chain is skipping or jumping, which is also caused by the lack of lubrication.

Troubleshooting a Chainsaw Chain Oiler

If you are experiencing any of the symptoms listed above, you should first try to troubleshoot the problem yourself. Here are a few things you can check:

Make sure that the oiler is turned on. The oiler may be turned off by a switch or a knob. Check to make sure that the switch is in the On position.
Check the oil level in the oil reservoir. The oil reservoir is located on the side of the chainsaw. Make sure that the oil level is between the Full and Empty marks. If the oil level is low, add more oil to the reservoir.
Check the oil line. The oil line runs from the oil reservoir to the chain. Make sure that the oil line is not kinked or damaged. If the oil line is damaged, you will need to replace it.
Check the oil pump. The oil pump is located inside the chainsaw. It is responsible for pumping oil from the reservoir to the chain. If the oil pump is not working properly, you will need to have it repaired or replaced.

If You Can’t Troubleshoot the Problem Yourself

If you are unable to troubleshoot the problem yourself, you should take your chainsaw to a qualified chainsaw repair shop. The technicians at the repair shop will be able to diagnose the problem and make the necessary repairs.

Preventing Chainsaw Chain Oiler Problems

You can help prevent chainsaw chain oiler problems by following these tips:

Keep the oil level in the reservoir full. A low oil level can cause the oiler to malfunction.
Change the oil regularly. The oil in the reservoir should be changed every 20-30 hours of use.
Inspect the oil line regularly. The oil line can become kinked or damaged over time. Inspect the oil line regularly and replace it if necessary.
Have your chainsaw serviced regularly. A qualified chainsaw repair shop can inspect your chainsaw for problems and make the necessary repairs.

By following these tips, you can help prevent chainsaw chain oiler problems and keep your chainsaw running smoothly.

Also Check: Husqvarna Chainsaw On Off Switch Not Working

FAQs: Husqvarna Chainsaw Chain Oiler Not Working

Why is my Husqvarna chainsaw chain oiler not working?

There are a few possible reasons why your Husqvarna chainsaw chain oiler might not be working. Here are some of the most common causes:

The oiler is not turned on. Make sure that the oiler switch is in the On position.
The oiler is clogged. The oiler can become clogged with sawdust or other debris, which can prevent the oil from flowing to the chain. To clean the oiler, remove the oiler cover and clean out the inside of the oiler with a small brush.
The oiler hose is kinked or damaged. The oiler hose can become kinked or damaged, which can prevent the oil from flowing to the chain. To check the oiler hose, inspect it for kinks or damage. If the hose is damaged, replace it with a new one.
The oiler pump is not working properly. The oiler pump can malfunction, which can prevent the oil from flowing to the chain. If the oiler pump is not working properly, you will need to have it repaired or replaced.

How do I fix a Husqvarna chainsaw chain oiler that is not working?

To fix a Husqvarna chainsaw chain oiler that is not working, you will need to identify the cause of the problem and then take the appropriate steps to fix it. Here are the steps to fix a Husqvarna chainsaw chain oiler that is not working:

1. Check to make sure that the oiler is turned on. The oiler switch is located on the side of the chainsaw. Make sure that the switch is in the On position.
2. Clean the oiler. The oiler can become clogged with sawdust or other debris, which can prevent the oil from flowing to the chain. To clean the oiler, remove the oiler cover and clean out the inside of the oiler with a small brush.
3. Check the oiler hose. The oiler hose can become kinked or damaged, which can prevent the oil from flowing to the chain. To check the oiler hose, inspect it for kinks or damage. If the hose is damaged, replace it with a new one.
4. Check the oiler pump. The oiler pump can malfunction, which can prevent the oil from flowing to the chain. If the oiler pump is not working properly, you will need to have it repaired or replaced.

What is the difference between a Husqvarna chainsaw chain oiler and a bar oiler?

A Husqvarna chainsaw chain oiler is a device that lubricates the chain of a chainsaw. The oiler is typically located on the side of the chainsaw and it dispenses oil onto the chain as the chainsaw is operated. A bar oiler is a device that lubricates the bar of a chainsaw. The bar oiler is typically located on the front of the chainsaw and it dispenses oil onto the bar as the chainsaw is operated.

How much oil does a Husqvarna chainsaw chain oiler use?

A Husqvarna chainsaw chain oiler uses a small amount of oil, typically about 1 ounce per hour. The amount of oil that the oiler uses will depend on the type of chainsaw and the conditions in which it is being used.

How do I adjust the oiler on my Husqvarna chainsaw?

The oiler on a Husqvarna chainsaw can be adjusted to provide the correct amount of oil to the chain. To adjust the oiler, follow these steps:

1. Locate the oiler adjustment screw. The oiler adjustment screw is located on the side of the chainsaw.
2. Turn the oiler adjustment screw clockwise to increase the amount of oil that is dispensed or counterclockwise to decrease the amount of oil that is dispensed.
3. Test the oiler to make sure that it is dispensing the correct amount of oil. The oiler should be dispensing enough oil to keep the chain lubricated but not so much oil that it is dripping off the chain.

 

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *