John Deere Chainsaw Bar Oiler Not Working: [Easy Fixes!]

As a chainsaw owner, there’s nothing more frustrating than having your bar oiler stop working. Not only can it be dangerous, but it can also lead to premature wear and tear on your saw. If your John Deere chainsaw bar oiler isn’t working, don’t despair. In this guide, we’ll walk you through the steps to troubleshoot and repair the problem quickly and easily.

We understand that your time is valuable, so we’ll get right to the point. We’ll start by discussing the common causes of bar oiler problems, and then we’ll walk you through the steps to diagnose and fix the issue. By the end of this guide, you’ll be able to get your chainsaw back up and running in no time.

Most Common Reasons Of John Deere Chainsaw Bar Oiler Not Working

No Oil in the Tank

The most common reason for a John Deere chainsaw bar oiler not working is that there is no oil in the tank. Check the oil level and add oil if necessary.

Clogged Oil Line

Another common cause of a John Deere chainsaw bar oiler not working is a clogged oil line. The oil line can become clogged with sawdust or dirt, preventing oil from reaching the bar and chain. To clean the oil line, remove the bar and chain and then use a small brush to clean out the inside of the oil line.

Blocked Oil Passages

The oil passages in the chainsaw can also become blocked with sawdust or dirt, preventing oil from reaching the bar and chain. To clean the oil passages, remove the bar and chain and then use a small brush to clean out the inside of the oil passages.

Faulty Oiler Valve

The oiler valve on a John Deere chainsaw can also malfunction, preventing oil from reaching the bar and chain. If you suspect that the oiler valve is faulty, you can try replacing it.

Low Oil Pressure

If the oil pressure in your John Deere chainsaw is low, it may not be able to properly lubricate the bar and chain. Low oil pressure can be caused by a number of factors, including a dirty air filter, a clogged oil filter, or a worn-out oil pump. To check the oil pressure, you can use a pressure gauge. If the oil pressure is low, you will need to troubleshoot the problem and fix it.

How to Troubleshoot: John Deere Chainsaw Bar Oiler Not Working

Symptoms

There are a few signs that your John Deere chainsaw bar oiler may not be working properly. These include:

The chain is not being lubricated properly, which can lead to overheating and damage to the chain and bar.
The oil level in the reservoir is low or empty.
The oiler is not pumping oil to the bar.
The oiler is clogged.

Troubleshooting

If you suspect that your John Deere chainsaw bar oiler is not working properly, you can troubleshoot the problem by following these steps:

1. Check the oil level in the reservoir. If the oil level is low or empty, fill the reservoir with the correct type of oil.
2. Make sure that the oiler is pumping oil to the bar. To do this, start the chainsaw and let it run for a few minutes. Then, look at the bar oiler and see if oil is flowing out of the nozzle. If no oil is flowing, the oiler may be clogged or defective.
3. If the oiler is clogged, you can try to clean it by removing the nozzle and using a small brush to clean out the inside of the oiler. If the oiler is defective, you will need to replace it.

Prevention

You can prevent problems with your John Deere chainsaw bar oiler by following these tips:

Keep the oil level in the reservoir full.
Use the correct type of oil for your chainsaw.
Clean the oiler regularly to prevent it from becoming clogged.

By following these tips, you can help to ensure that your John Deere chainsaw bar oiler works properly and that your chainsaw stays in good condition.

Also Check: Jonsered Chainsaw Oiler Not Working

FAQs: John Deere Chainsaw Bar Oiler Not Working

Why is my John Deere chainsaw bar oiler not working?

There are a few reasons why your John Deere chainsaw bar oiler might not be working. Here are some of the most common causes:

The oiler is clogged. The oiler can become clogged with sawdust or other debris, which can prevent the oil from flowing to the bar and chain. To fix this, you can try cleaning the oiler with a small brush or needle.
The oiler is not adjusted properly. The oiler needs to be adjusted so that it delivers the correct amount of oil to the bar and chain. If the oiler is adjusted too low, the bar and chain will not be lubricated properly. If the oiler is adjusted too high, the bar and chain will be over-lubricated, which can cause the saw to run poorly.
The oiler is broken. If the oiler is broken, it will not be able to deliver any oil to the bar and chain. If you suspect that the oiler is broken, you should take your chainsaw to a qualified service center for repairs.

How do I fix a clogged John Deere chainsaw bar oiler?

To fix a clogged John Deere chainsaw bar oiler, you can try the following steps:

1. Turn off the chainsaw and disconnect the spark plug wire.
2. Remove the oiler cover.
3. Use a small brush or needle to clean out the oiler.
4. Reinstall the oiler cover.
5. Reattach the spark plug wire.

How do I adjust the oiler on my John Deere chainsaw?

To adjust the oiler on your John Deere chainsaw, you can follow these steps:

1. Turn off the chainsaw and disconnect the spark plug wire.
2. Locate the oiler adjustment screw.
3. Turn the adjustment screw clockwise to increase the amount of oil that is delivered to the bar and chain. Turn the adjustment screw counterclockwise to decrease the amount of oil that is delivered to the bar and chain.
4. Reattach the spark plug wire.

What happens if my John Deere chainsaw bar oiler is not working?

If your John Deere chainsaw bar oiler is not working, the bar and chain will not be lubricated properly. This can lead to the following problems:

The bar and chain will wear out faster.
The bar and chain will be more difficult to operate.
The bar and chain may become damaged.

How can I prevent my John Deere chainsaw bar oiler from malfunctioning?

To prevent your John Deere chainsaw bar oiler from malfunctioning, you can follow these tips:

Keep the oiler clean and free of debris.
Inspect the oiler regularly for signs of wear or damage.
Replace the oiler if it is damaged.
Use the correct type of oil for your chainsaw.
Follow the manufacturer’s instructions for operating and maintaining your chainsaw.