Lever On Pump Pressure Washer Not Working [Here’S The Fix!]

Do you own a pressure washer that isn’t working properly

If the lever on your pump pressure washer isn’t working, you’re not alone. This is a common problem that can be frustrating and inconvenient. But don’t worry, there’s a good chance you can fix it yourself.

In this guide, I’ll walk you through the steps of troubleshooting a pressure washer that isn’t working. I’ll cover the most common causes of this problem and provide instructions on how to fix them.

By the end of this guide, you’ll be able to get your pressure washer up and running again in no time.

Reasons Why Lever On Pump Pressure Washer Not Working

1. Faulty Pressure Washer Pump

The most common reason for a pressure washer lever not working is a faulty pump. This can be caused by a number of factors, including:

Damaged or worn seals:
The seals in a pressure washer pump help to create a tight seal between the pump and the cylinder, preventing fluid from leaking out. If these seals are damaged or worn, fluid can leak out, which can cause the pump to lose pressure and the lever to stop working.

Clogged or damaged valves:
The valves in a pressure washer pump control the flow of fluid through the pump. If these valves are clogged or damaged, fluid can’t flow through the pump properly, which can also cause the pump to lose pressure and the lever to stop working.

Debris in the pump:
Debris, such as dirt or sand, can get into the pump and damage the seals, valves, or other components. This can also cause the pump to lose pressure and the lever to stop working.

2. Faulty Pressure Washer Hose

The hose on a pressure washer can also be a cause of the lever not working. If the hose is kinked or damaged, it can restrict the flow of fluid through the pump, which can cause the pump to lose pressure and the lever to stop working.

3. Faulty Pressure Washer Trigger

The trigger on a pressure washer is another potential cause of the lever not working. If the trigger is stuck or damaged, it can prevent the lever from being activated, which can also cause the pump to lose pressure.

4. Low Fluid Level

If the fluid level in the pressure washer is too low, it can cause the pump to lose pressure and the lever to stop working. This is because the pump needs a certain amount of fluid in order to operate properly.

5. Blocked Inlet Filter

The inlet filter on a pressure washer helps to prevent debris from entering the pump. If this filter is blocked, it can restrict the flow of fluid into the pump, which can cause the pump to lose pressure and the lever to stop working.

How to Troubleshoot: Lever on Pump Pressure Washer Not Working

Your pressure washer is a valuable tool for cleaning your home, car, and other outdoor surfaces. But what happens when the lever on the pump doesn’t work? This can be a frustrating problem, but it’s usually easy to fix. In this blog post, we’ll walk you through the steps of troubleshooting a pressure washer that’s not working.

Step 1: Check the power

The first thing you need to do is check to make sure that the pressure washer is getting power. To do this, simply plug it in and turn it on. If the power light comes on, then you know that the problem is not with the power supply. If the power light doesn’t come on, then you’ll need to check the outlet to make sure that it’s working properly.

Step 2: Check the hose

Once you’ve confirmed that the pressure washer is getting power, you need to check the hose. Make sure that it’s not kinked or damaged. If it is, then you’ll need to replace it.

Step 3: Check the pump

The next thing you need to do is check the pump. To do this, you’ll need to remove the cover. Once you’ve removed the cover, you’ll be able to see the pump. Look for any signs of damage or wear. If you see any damage, then you’ll need to replace the pump.

Step 4: Check the pressure switch

The pressure switch is a small device that controls the flow of water to the pump. To check the pressure switch, you’ll need to use a multimeter. Connect the multimeter to the pressure switch and turn on the pressure washer. The multimeter should show a reading of 120 volts. If the multimeter doesn’t show a reading of 120 volts, then you’ll need to replace the pressure switch.

Step 5: Check the relief valve

The relief valve is a small valve that prevents the pump from overpressurizing. To check the relief valve, you’ll need to use a screwdriver. Remove the screw that holds the relief valve in place. Once you’ve removed the screw, you’ll be able to see the relief valve. Look for any signs of damage or wear. If you see any damage, then you’ll need to replace the relief valve.

Step 6: Check the water inlet valve

The water inlet valve is a small valve that controls the flow of water into the pump. To check the water inlet valve, you’ll need to use a screwdriver. Remove the screw that holds the water inlet valve in place. Once you’ve removed the screw, you’ll be able to see the water inlet valve. Look for any signs of damage or wear. If you see any damage, then you’ll need to replace the water inlet valve.

Step 7: Check the o-rings

The o-rings are small rubber rings that seal the various parts of the pressure washer together. To check the o-rings, you’ll need to use a magnifying glass. Look for any signs of damage or wear. If you see any damage, then you’ll need to replace the o-rings.

Step 8: Reassemble the pressure washer

Once you’ve completed all of the steps above, you can reassemble the pressure washer. Be sure to tighten all of the screws securely.

Conclusion

By following these steps, you can troubleshoot a pressure washer that’s not working. If you’re still having trouble, then you may need to take your pressure washer to a qualified technician.

Also Read: Low Pressure Siphon Not Working Pressure Washer

FAQs: Lever on Pump Pressure Washer Not Working

Why is the lever on my pressure washer not working?

There are a few possible reasons why the lever on your pressure washer may not be working.

The lever may be stuck: If the lever is stuck, you can try to free it by spraying some WD-40 or other lubricant into the mechanism and working the lever back and forth. If this doesn’t work, you may need to replace the lever.

The lever may be broken: If the lever is broken, you will need to replace it.

The pressure washer may be turned off: Make sure that the pressure washer is turned on and that the water is flowing.

The pressure washer may be out of gas: If the pressure washer is out of gas, you will need to refill it.

How do I fix a stuck lever on my pressure washer?

To fix a stuck lever on your pressure washer, you can try the following:

1. Spray some WD-40 or other lubricant into the mechanism and work the lever back and forth.
2. Use a thin object, such as a screwdriver, to pry the lever loose.
3. Replace the lever if it is broken.

How do I replace the lever on my pressure washer?

To replace the lever on your pressure washer, you will need to:

1. Turn off the pressure washer and disconnect it from the water supply.
2. Remove the old lever by unscrewing the screws that hold it in place.
3. Install the new lever by screwing it into place.
4. Reattach the pressure washer to the water supply and turn it on.

Why is my pressure washer not building pressure?

There are a few possible reasons why your pressure washer may not be building pressure.

The pump may be damaged: If the pump is damaged, it will not be able to build pressure.

The hose may be kinked or clogged: If the hose is kinked or clogged, it will not be able to transfer water to the pump.

The nozzle may be clogged: If the nozzle is clogged, it will not be able to release water at a high pressure.

The water supply may be too low: If the water supply is too low, the pump will not be able to build pressure.

How do I fix a pressure washer that is not building pressure?

To fix a pressure washer that is not building pressure, you can try the following:

1. Check the pump for damage. If the pump is damaged, it will need to be replaced.
2. Check the hose for kinks or clogs. If the hose is kinked or clogged, it will need to be replaced or cleared.
3. Check the nozzle for clogs. If the nozzle is clogged, it will need to be cleaned or replaced.
4. Check the water supply. If the water supply is too low, it will need to be increased.

How do I prevent my pressure washer from leaking?

To prevent your pressure washer from leaking, you can try the following:

1. Tighten all of the connections on the pressure washer.
2. Use a high-quality hose that is not kinked or damaged.
3. Use a high-quality nozzle that is not clogged.
4. Keep the pressure washer clean and free of debris.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *