North Star Pressure Washer Pump Not Working [With Solution]

If your North Star pressure washer pump isn’t working, you know how frustrating it can be. You can’t clean your driveway, your siding, or your car. You might even be worried about a bigger problem.

But don’t worry, you’re not alone. Pressure washer pumps are one of the most common problems with these machines. And in most cases, the fix is simple.

In this guide, I’ll walk you through the steps to troubleshoot a North Star pressure washer pump that’s not working. I’ll show you how to identify the problem, and how to fix it quickly and easily.

So if your pressure washer is giving you trouble, read on. I’ll help you get it up and running again in no time.

Reasons Why North Star Pressure Washer Pump Not Working

Reasons Why North Star Pressure Washer Pump Not Working

Dirty or clogged filter: The most common cause of a pressure washer pump not working is a dirty or clogged filter. The filter prevents dirt and debris from entering the pump, and if it becomes clogged, it can restrict the flow of water and prevent the pump from generating pressure. To fix this problem, remove the filter and clean it with a hose. If the filter is damaged, replace it with a new one.

Low water pressure: If the water pressure at your home is low, it can also cause the pressure washer pump to not work properly. To check the water pressure, turn on a faucet and measure the pressure with a pressure gauge. If the pressure is below 40 psi, you will need to increase the water pressure to get the pressure washer to work properly. You can do this by turning on the water main to your house or by installing a pressure booster pump.

Defective pump: If the pressure washer pump is defective, it will not be able to generate pressure. To check the pump, turn on the pressure washer and listen for the pump to start. If you do not hear the pump running, or if the pump is running but not generating pressure, the pump is likely defective and will need to be replaced.

Blocked hose: A blocked hose can also prevent the pressure washer from generating pressure. To check the hose, disconnect it from the pump and run water through it. If the water does not flow freely, the hose is blocked and will need to be cleaned or replaced.

Incorrect oil level: Some pressure washers require oil to lubricate the pump. If the oil level is too low, the pump will not be able to generate pressure. To check the oil level, refer to the owner’s manual for your pressure washer. If the oil level is low, add oil to the pump until it reaches the proper level.

How to Troubleshoot And Fix: north star pressure washer pump not working

Symptoms of a North Star Pressure Washer Pump Not Working

There are a few different symptoms that can indicate that your North Star pressure washer pump is not working properly. These include:

The pressure washer is not producing any pressure
The pressure washer is producing low pressure
The pressure washer is making a loud whining or buzzing noise
The pressure washer is leaking fluid
The pressure washer is overheating

Causes of a North Star Pressure Washer Pump Not Working

There are a number of different things that can cause a North Star pressure washer pump to stop working. These include:

A clogged filter
A faulty pressure switch
A broken pump impeller
A damaged pump housing
A leaking gasket
A seized pump shaft

How to Troubleshoot a North Star Pressure Washer Pump

To troubleshoot a North Star pressure washer pump, you will need to:

1. Inspect the filter for clogs. If the filter is clogged, clean it or replace it.
2. Check the pressure switch. If the pressure switch is faulty, replace it.
3. Inspect the pump impeller. If the impeller is damaged, replace it.
4. Inspect the pump housing. If the pump housing is damaged, replace it.
5. Inspect the gaskets. If the gaskets are leaking, replace them.
6. Inspect the pump shaft. If the pump shaft is seized, replace it.

How to Fix a North Star Pressure Washer Pump

Once you have identified the cause of the problem, you can fix the North Star pressure washer pump by:

Cleaning or replacing the filter
Replacing the pressure switch
Replacing the pump impeller
Replacing the pump housing
Replacing the gaskets
Replacing the pump shaft

Preventing North Star Pressure Washer Pump Problems

You can help prevent North Star pressure washer pump problems by:

Keeping the filter clean
Replacing the filter regularly
Inspecting the pressure switch regularly
Replacing the pressure switch as needed
Inspecting the pump impeller regularly
Replacing the pump impeller as needed
Inspecting the pump housing regularly
Replacing the pump housing as needed
Inspecting the gaskets regularly
Replacing the gaskets as needed
Inspecting the pump shaft regularly
Replacing the pump shaft as needed

Also Read: Northstar Pressure Washer Pump Not Working

FAQs: North Star Pressure Washer Pump Not Working

Why is my North Star pressure washer pump not working?

There are a few possible reasons why your North Star pressure washer pump might not be working. Here are some of the most common causes:

The pump is not getting enough water: Make sure that the water supply to the pump is turned on and that there is no blockage in the hose.

The pump is overheating: If the pump is running for too long without a break, it can overheat and stop working. Allow the pump to cool down for a few minutes before using it again.

The pump is clogged: The pump can become clogged with dirt and debris, which can prevent it from pumping water. To clean the pump, remove the inlet screen and clean it with a brush.

The pump is damaged: If the pump is damaged, it will need to be repaired or replaced.

How do I fix a North Star pressure washer pump that is not working?

Once you have determined the cause of the problem, you can try to fix the pump yourself. Here are some tips:

Check the water supply: Make sure that the water supply to the pump is turned on and that there is no blockage in the hose.

Let the pump cool down: If the pump is overheating, allow it to cool down for a few minutes before using it again.

Clean the pump: Remove the inlet screen and clean it with a brush.

Replace the pump: If the pump is damaged, it will need to be repaired or replaced.

What are the symptoms of a bad North Star pressure washer pump?

Here are some of the symptoms of a bad North Star pressure washer pump:

The pump is not making any noise.
The pump is making a loud noise.
The pump is not pumping water.
The pump is leaking water.
The pump is overheating.

How much does it cost to replace a North Star pressure washer pump?

The cost of replacing a North Star pressure washer pump will vary depending on the model of the pump and the location where you purchase it. However, you can expect to pay anywhere from $50 to $100 for a new pump.

How can I prevent my North Star pressure washer pump from failing?

There are a few things you can do to prevent your North Star pressure washer pump from failing:

Use the pump properly: Do not overload the pump or run it for too long without a break.

Maintain the pump regularly: Clean the pump regularly and replace the inlet screen as needed.

Store the pump properly: When you are not using the pump, store it in a cool, dry place.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *