Pressure Washer Lance Not Working [Step-By-Step Fixes]

There’s nothing more frustrating than having a pressure washer that doesn’t work properly. Whether you’re trying to clean your driveway, your deck, or your car, a broken pressure washer can be a major pain. But don’t despair! In this guide, we’ll show you how to troubleshoot a pressure washer lance that’s not working. We’ll cover everything from common causes of the problem to simple fixes that you can do yourself. So if your pressure washer is acting up, read on for help getting it back in working order.

Reasons Why Pressure Washer Lance Not Working

No Water Flow

Blocked nozzle:

The most common cause of a pressure washer lance not working is a blocked nozzle. This can be caused by dirt, debris, or mineral buildup. To fix this, remove the nozzle and clean it with a brush or compressed air.

Clogged hose:

Another common cause of a pressure washer lance not working is a clogged hose. This can be caused by dirt, debris, or mineral buildup. To fix this, disconnect the hose from the pressure washer and the gun and clean it with a brush or compressed air.

Damaged hose:

A damaged hose can also prevent water from flowing through the lance. If the hose is kinked, cracked, or otherwise damaged, it will need to be replaced.

Pressure washer not turned on:

Make sure that the pressure washer is turned on and that the water is turned on to the pressure washer.

Low water pressure:

If the water pressure is too low, the pressure washer will not be able to generate enough power to push the water through the lance. To fix this, check the water supply to the pressure washer and make sure that it is turned on and flowing at a high enough pressure.

Water Leaking from the Lance

Loose nozzle:

If the nozzle is not tightened all the way onto the gun, it can leak water. To fix this, tighten the nozzle until it is snug.

Damaged nozzle:

A damaged nozzle can also cause water to leak from the lance. If the nozzle is cracked or otherwise damaged, it will need to be replaced.

O-rings:

The O-rings on the nozzle and gun can wear out over time and allow water to leak. To fix this, replace the O-rings.

Pressure Washer Lance Not Firing

Trigger not pulled:

Make sure that the trigger on the gun is pulled all the way back. If the trigger is not pulled, the pressure washer will not fire.

Pressure washer not primed:

If the pressure washer is not primed, it will not fire. To prime the pressure washer, follow the instructions in the owner’s manual.

Pressure washer hose kinked:

If the pressure washer hose is kinked, it will prevent the pressure washer from firing. To fix this, straighten out the hose.

Pressure washer pump not working:

If the pressure washer pump is not working, it will not fire. To fix this, have the pressure washer repaired or serviced.

How to Troubleshoot And Fix: Pressure Washer Lance Not Working

Your pressure washer lance is one of the most important parts of your machine. It’s responsible for delivering the water and cleaning solution to the surface you’re cleaning. If your lance isn’t working properly, you won’t be able to get the job done.

There are a few different reasons why your pressure washer lance might not be working. In this article, we’ll discuss some of the most common causes and how to fix them.

Causes of a Pressure Washer Lance Not Working

There are a number of different reasons why your pressure washer lance might not be working. Some of the most common causes include:

Clogged nozzle:

The nozzle on your pressure washer lance is responsible for controlling the flow of water and cleaning solution. If the nozzle becomes clogged, it can restrict the flow of water and prevent the lance from working properly.

Damaged O-ring:

The O-ring on your pressure washer lance helps to create a seal between the lance and the gun. If the O-ring is damaged, it can leak water and prevent the lance from working properly.

Broken trigger:

The trigger on your pressure washer lance is responsible for controlling the flow of water. If the trigger is broken, it can prevent you from turning the lance on or off.

Faulty hose:

The hose on your pressure washer lance connects the lance to the gun. If the hose is damaged, it can leak water and prevent the lance from working properly.

How to Fix a Pressure Washer Lance Not Working

Once you’ve identified the cause of the problem, you can usually fix it yourself. Here are the steps to fix a pressure washer lance that’s not working:

1. Clogged nozzle:

To clean a clogged nozzle, first remove the nozzle from the lance. Then, use a toothpick or needle to carefully remove any debris that may be blocking the nozzle. Once the nozzle is clear, reattach it to the lance and test it to make sure it’s working properly.

2. Damaged O-ring:

To replace a damaged O-ring, first remove the nozzle from the lance. Then, use a pair of pliers to carefully pry the old O-ring out of place. Once the old O-ring is removed, insert the new O-ring into the nozzle. Finally, reattach the nozzle to the lance and test it to make sure it’s working properly.3. Broken trigger:

To fix a broken trigger, first remove the trigger from the lance. Then, use a screwdriver to carefully remove the old trigger. Once the old trigger is removed, insert the new trigger into the lance and secure it in place with the screwdriver. Finally, reattach the trigger to the lance and test it to make sure it’s working properly.

4. Faulty hose:

To fix a faulty hose, first disconnect the hose from the lance and the gun. Then, use a pair of pliers to carefully cut the hose in half. Once the hose is cut in half, remove the old hose and replace it with a new hose. Finally, reconnect the hose to the lance and the gun and test it to make sure it’s working properly.

Preventative Maintenance

The best way to prevent problems with your pressure washer lance is to perform regular preventative maintenance. Here are a few tips to help you keep your lance in good working order:

Clean the nozzle regularly:

Clogged nozzles are one of the most common causes of pressure washer lance problems. To prevent this, make sure to clean the nozzle regularly. You can do this by removing the nozzle from the lance and soaking it in a vinegar and water solution for a few minutes. Then, rinse the nozzle thoroughly with water and dry it with a towel.

Inspect the O-ring regularly:

The O-ring on your pressure washer lance is a critical component. If the O-ring is damaged, it can leak water and prevent the lance from working properly. To prevent this, inspect the O-ring regularly for signs of damage. If the O-ring is damaged, replace it immediately.

Store your pressure washer lance properly:

When you’re not using your pressure washer lance, it’s important to store it properly. This will help to prevent damage to the lance and keep it in good working order. To store your pressure washer lance properly, first disconnect the hose from the lance and the gun. Then, place the lance in a safe, dry location.

By following these tips, you can help to prevent problems with your pressure washer lance and keep it in good working order for years to come

Also Read: Pressure Washer Not Working Correctly

FAQs: Pressure washer lance not working

Why is my pressure washer lance not working?

There are a few possible reasons why your pressure washer lance may not be working. Here are some of the most common causes:

The lance is clogged: This is the most common cause of a pressure washer lance not working. If the lance is clogged with dirt, debris, or soap, it will not be able to produce a strong stream of water. To fix this problem, you can try cleaning the lance with a wire brush or a garden hose.

The lance is damaged: If the lance is damaged, it may not be able to produce a strong stream of water. To fix this problem, you will need to replace the lance.

The pressure washer is not producing enough pressure: If the pressure washer is not producing enough pressure, the lance will not be able to produce a strong stream of water. To fix this problem, you can try adjusting the pressure on the pressure washer.

The pressure washer is not turned on: If the pressure washer is not turned on, the lance will not be able to produce a stream of water. To fix this problem, you will need to turn on the pressure washer.

How do I clean a clogged pressure washer lance?

To clean a clogged pressure washer lance, you can use a wire brush or a garden hose. Here are the steps:

1. Turn off the pressure washer and disconnect the lance from the pressure washer.
2. If the lance is made of metal, use a wire brush to clean the inside of the lance.
3. If the lance is made of plastic, use a garden hose to rinse the inside of the lance.
4. Reattach the lance to the pressure washer and turn on the pressure washer.

How do I replace a pressure washer lance?

To replace a pressure washer lance, you will need to:

1. Turn off the pressure washer and disconnect the lance from the pressure washer.
2. Remove the old lance by unscrewing it from the pressure washer.
3. Insert the new lance into the pressure washer and tighten it until it is secure.
4. Turn on the pressure washer and test the new lance.

How do I adjust the pressure on my pressure washer?

To adjust the pressure on your pressure washer, you will need to:

1. Find the pressure adjustment knob on the pressure washer.
2. Turn the knob clockwise to increase the pressure or counterclockwise to decrease the pressure.
3. Test the pressure by spraying the water on a piece of wood or concrete.

What should I do if my pressure washer is not turning on?

If your pressure washer is not turning on, you can try the following:

1. Check the power cord to make sure it is plugged in and turned on.
2. Check the fuse to make sure it is not blown.
3. Check the oil level to make sure it is not low.
4. Check the spark plug to make sure it is clean and properly gapped.
5. If you have checked all of these things and the pressure washer still is not turning on, you may need to take it to a qualified technician for repairs.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *