Why Won’t Your Ryobi Gas Chainsaw Start?
Here’s What to Do
Your Ryobi gas chainsaw is a powerful tool that can make quick work of cutting firewood, clearing brush, and trimming trees. But when it won’t start, it can be a major pain.
Here are a few things to check if your
Is the chain oil level correct If the chain oil level is too low, the chainsaw won’t be able to generate enough compression to start.
Is the spark plug properly gapped A spark plug that is not properly gapped can cause the chainsaw to misfire and not start.
Is the air filter clean A dirty air filter can restrict airflow to the carburetor, causing the chainsaw to run lean and not start.
Is the carburetor adjusted correctly The carburetor is responsible for mixing the fuel and air in the correct proportions. If the carburetor is not adjusted correctly, the chainsaw may not start or run properly.
If you have checked all of these things and your Ryobi gas chainsaw still won’t start, it’s time to take it to a qualified technician for repairs.
Ryobi Gas Chainsaw Won’T Start
There are a few reasons why your Ryobi gas chainsaw might not start.
The spark plug is not firing:
Check to make sure the spark plug is installed correctly and that the gap is set properly. If the spark plug is wet, dry it off with a clean cloth.
The carburetor is not adjusted properly:
The carburetor controls the amount of fuel and air that is mixed together to create the fuel/air mixture that is sent to the engine. If the carburetor is not adjusted properly, the engine will not run properly.
The fuel filter is clogged:
The fuel filter prevents dirt and debris from entering the carburetor. If the fuel filter is clogged, it will restrict the flow of fuel to the carburetor and the engine will not run properly.
The air filter is dirty:
The air filter prevents dirt and debris from entering the engine. If the air filter is dirty, it will restrict the flow of air to the engine and the engine will not run properly.
Ryobi Gas Chainsaw Won’t Start
Troubleshooting a Ryobi Gas Chainsaw
If your Ryobi gas chainsaw won’t start, there are a few things you can check to troubleshoot the problem.
Check the fuel level:
Make sure that the chainsaw has enough fuel in the tank. If the tank is empty, fill it up with fresh gasoline.
Check the spark plug:
Remove the spark plug and inspect it for damage. If the spark plug is fouled or damaged, replace it with a new one.
Check the air filter:
Remove the air filter and inspect it for dirt or debris. If the air filter is dirty, clean it or replace it with a new one.
Check the carburetor:
The carburetor is responsible for mixing the fuel and air in the correct proportions. If the carburetor is dirty or malfunctioning, it can cause the chainsaw to not start. You can clean the carburetor yourself or take it to a qualified technician to have it repaired.
Check the starter rope:
The starter rope is used to pull the engine over and start it. If the starter rope is frayed or damaged, it may not be able to pull the engine over. Replace the starter rope if necessary.
If you have checked all of these things and your Ryobi gas chainsaw still won’t start, you may need to take it to a qualified technician for further diagnosis and repair:
Preventative Maintenance
The best way to avoid problems with your Ryobi gas chainsaw is to perform regular preventative maintenance. This includes:
Checking the fuel level and oil level regularly:
Cleaning the air filter regularly:
Adjusting the carburetor regularly:
Replacing the spark plug regularly:
Inspecting the starter rope regularly:
By following these simple maintenance tips, you can help to keep your Ryobi gas chainsaw running smoothly and efficiently.
Also Read: 1980 Craftman Chainsaw Won’T Pump Gas
FAQs: Ryobi Gas Chainsaw Won’t Start
Why won’t my Ryobi gas chainsaw start?
There are a few possible reasons why your Ryobi gas chainsaw won’t start. Here are the most common:
The chainsaw is out of gas: Make sure that the chainsaw has gas in the tank and that the fuel valve is open.
The spark plug is fouled: Remove the spark plug and clean it with a wire brush. If the spark plug is damaged, replace it with a new one.
The carburetor is dirty: Clean the carburetor according to the manufacturer’s instructions.
The air filter is dirty: Clean or replace the air filter according to the manufacturer’s instructions.
The chainsaw is not getting enough compression: This could be caused by a problem with the piston, cylinder, or valves. If you suspect that the chainsaw is not getting enough compression, take it to a qualified repair shop.
What should I do if my Ryobi gas chainsaw starts but then dies?
If your Ryobi gas chainsaw starts but then dies, there are a few possible causes. Here are the most common:
The chainsaw is not getting enough fuel: Make sure that the fuel valve is open and that the carburetor is adjusted properly.
The chainsaw is not getting enough air: Check the air filter for dirt and debris. If the air filter is dirty, clean or replace it.
The chainsaw is overheating: Allow the chainsaw to cool down before starting it again.
The chainsaw is not getting enough compression: This could be caused by a problem with the piston, cylinder, or valves. If you suspect that the chainsaw is not getting enough compression, take it to a qualified repair shop.
How do I adjust the carburetor on my Ryobi gas chainsaw?
To adjust the carburetor on your Ryobi gas chainsaw, follow these steps:
1. Turn off the chainsaw and allow it to cool down.
2. Remove the air filter cover.
3. Locate the carburetor adjustment screws. There are two screws, one for the high speed and one for the low speed.
4. Turn the high speed screw clockwise to increase the speed or counterclockwise to decrease the speed.
5. Turn the low speed screw clockwise to increase the speed or counterclockwise to decrease the speed.
6. Reinstall the air filter cover.
7. Start the chainsaw and test the adjustments.
How do I clean the spark plug on my Ryobi gas chainsaw?
To clean the spark plug on your Ryobi gas chainsaw, follow these steps:
1. Turn off the chainsaw and allow it to cool down.
2. Remove the spark plug cap.
3. Use a spark plug wrench to remove the spark plug.
4. Clean the spark plug with a wire brush.
5. Apply a small amount of anti-seize compound to the threads of the spark plug.
6. Reinstall the spark plug and tighten it to the specified torque.
How do I clean the air filter on my Ryobi gas chainsaw?
To clean the air filter on your Ryobi gas chainsaw, follow these steps:
1. Turn off the chainsaw and allow it to cool down.
2. Remove the air filter cover.
3. Remove the air filter.
4. Wash the air filter in warm, soapy water.
5. Rinse the air filter in clean water.
6. Dry the air filter completely.
7. Reinstall the air filter.