Soap Is Not Working On Sun Joe Pressure Washer [Easy Fixes!]

There’s nothing more frustrating than having a pressure washer that’s not working properly. And when it comes to Sun Joe pressure washers, one of the most common problems is that the soap isn’t working. This can be a major inconvenience, especially if you’re trying to clean something that’s really dirty.

In this guide, I’ll walk you through the steps to troubleshoot the issue of soap not working on your Sun Joe pressure washer. I’ll also provide some tips on how to prevent this problem from happening in the future. So if you’re ready to get your pressure washer back up and running, let’s get started!

Reasons Why Soap Is Not Working On Sun Joe Pressure Washer

Incorrect Soap Type

The most common reason why soap is not working on a Sun Joe pressure washer is because the wrong type of soap is being used. Sun Joe pressure washers are designed to use a specific type of soap, which is typically a concentrated detergent. If you use a different type of soap, such as a dish soap or laundry detergent, it will not work properly and may even damage your pressure washer.

Incorrect Soap Concentration

Another common reason why soap is not working on a Sun Joe pressure washer is because the soap is not being used at the correct concentration. The correct concentration of soap for a Sun Joe pressure washer is typically between 1 and 2 percent. If you use too much soap, it will not rinse off properly and may clog the spray nozzle. If you use too little soap, it will not be effective in cleaning your surfaces.

Dirty Soap Tank

If the soap tank on your Sun Joe pressure washer is dirty, it can prevent the soap from being properly dispensed. To clean the soap tank, you will need to remove it from the pressure washer and rinse it out with warm water. You may also need to use a degreaser to remove any stubborn dirt or grease.

Clogged Spray Nozzle

If the spray nozzle on your Sun Joe pressure washer is clogged, it can prevent the soap from being properly sprayed out. To clean the spray nozzle, you will need to remove it from the pressure washer and use a small brush to loosen any debris. You may also need to use a toothpick or needle to remove any stubborn clogs.

Faulty Pressure Washer

In rare cases, the soap may not be working on your Sun Joe pressure washer because there is a problem with the pressure washer itself. If you have tried all of the other troubleshooting steps and the soap is still not working, you may need to have your pressure washer repaired or serviced.

How to Troubleshoot And Fix: soap is not working on sun joe pressure washer

Symptoms

Soap not coming out of the wand when you press the trigger
Soap leaking from the back of the pressure washer
Pressure washer making a whining noise when you press the trigger

Causes

The soap container is not properly attached to the pressure washer
The soap hose is kinked or blocked
The soap pump is not working properly
The pressure washer is not getting enough water

Solutions

Make sure that the soap container is properly attached to the pressure washer.
Check the soap hose for kinks or blockages.
Clean or replace the soap pump if it is not working properly.
Check the water supply to the pressure washer. Make sure that the water is turned on and that the pressure washer is getting enough water.

Prevention

Make sure that the soap container is properly attached to the pressure washer before you use it.
Check the soap hose for kinks or blockages before you use it.
Clean or replace the soap pump if it is not working properly.
Check the water supply to the pressure washer regularly to make sure that it is getting enough water.

Conclusion

If you are having trouble with your Sun Joe pressure washer not dispensing soap, you can troubleshoot the problem by following the steps in this article. If you are unable to fix the problem yourself, you can contact Sun Joe customer service for assistance.

Also Read: Soap Not Working Mi T M Pressure Washer

FAQs: Soap Not Working on Sun Joe Pressure Washer

Why is soap not working on my Sun Joe pressure washer?

There are a few reasons why soap might not be working on your Sun Joe pressure washer.

The soap is not compatible with the pressure washer: Make sure that the soap you are using is specifically designed for use with pressure washers. Some soaps can damage the pump or other components of the pressure washer.

The soap is not being applied correctly: You need to apply the soap to the surface you are cleaning in a thin, even layer. If you apply too much soap, it can clog the nozzle and prevent the soap from being sprayed out.

The pressure washer is not set to the correct pressure: The pressure washer needs to be set to a high enough pressure to break down the soap and allow it to penetrate the surface you are cleaning. If the pressure is too low, the soap will not be effective.

The water temperature is too low: The water temperature needs to be warm enough to activate the soap. If the water is too cold, the soap will not work properly.

How do I fix soap not working on my Sun Joe pressure washer?

To fix soap not working on your Sun Joe pressure washer, try the following:

Use a soap that is specifically designed for use with pressure washers:

Apply the soap to the surface you are cleaning in a thin, even layer:

Set the pressure washer to the correct pressure:

Make sure the water temperature is warm enough to activate the soap:

If you have tried these steps and the soap is still not working, you may need to have the pressure washer serviced.

What kind of soap should I use with my Sun Joe pressure washer?

You should use a soap that is specifically designed for use with pressure washers. These soaps are formulated to be safe for the pump and other components of the pressure washer, and they will produce a thick, sudsy lather that is effective at cleaning surfaces.

Some popular brands of soap for pressure washers include:

Sun Joe Pressure Washer Soap
Simple Green Pressure Washer Cleaner
Karcher Pressure Washer Soap
OMO Pressure Washer Soap
Mr. Clean Pressure Washer Cleaner

How do I apply soap to my Sun Joe pressure washer?

To apply soap to your Sun Joe pressure washer, follow these steps:

1. Turn on the pressure washer and allow it to warm up for a few minutes.
2. Attach the soap dispenser to the pressure washer.
3. Fill the soap dispenser with soap.
4. Turn on the soap dispenser.
5. Spray the soap onto the surface you are cleaning.
6. Rinse the surface with clean water.

What pressure should I use for soap on my Sun Joe pressure washer?

The ideal pressure for soap on a Sun Joe pressure washer is between 1500 and 2000 PSI. This pressure is high enough to break down the soap and allow it to penetrate the surface you are cleaning, but it is not so high that it will damage the surface.

What water temperature should I use for soap on my Sun Joe pressure washer?

The ideal water temperature for soap on a Sun Joe pressure washer is between 100° and 110° F. This temperature is warm enough to activate the soap, but it is not so hot that it will damage the surface you are cleaning.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *