Sunjoe Pressure Washer Soap Not Working [How To Fix It Instantly]

Do you have a SunJoe pressure washer that’s not dispensing soap You’re not alone. This is a common problem, and it can be frustrating and inconvenient. But don’t worry, there’s a simple solution. In this guide, I’ll walk you through the steps to troubleshoot the issue and get your pressure washer back up and running in no time.

Most Common Reasons Of Sunjoe Pressure Washer Soap Not Working

Most Common Reasons Of Sunjoe Pressure Washer Soap Not Working

1. Insufficient Soap

The most common reason for Sunjoe pressure washer soap not working is that there is not enough soap in the reservoir. Make sure to fill the reservoir to the recommended level before using the pressure washer.

2. Wrong Type of Soap

Another common reason for Sunjoe pressure washer soap not working is that you are using the wrong type of soap. Only use soaps that are specifically designed for use with pressure washers. Avoid using dish soap, laundry detergent, or other household cleaners, as these can damage the pressure washer.

3. Clogged Soap Nozzle

If the soap nozzle is clogged, it can prevent the soap from being properly dispensed. To clean the soap nozzle, remove it from the pressure washer and rinse it with warm water. You can also use a toothpick or needle to gently clear any obstructions.

4. Low Pressure

If the pressure washer is not generating enough pressure, the soap will not be able to properly penetrate the surface of the object being cleaned. To check the pressure, look at the pressure gauge on the pressure washer. If the pressure is below the recommended level, you may need to clean the filter or replace the pump.

5. Faulty Soap Dispenser

If the soap dispenser is faulty, it may not be able to properly dispense the soap. To check the soap dispenser, remove it from the pressure washer and inspect it for damage. If the dispenser is damaged, you will need to replace it.

How to Troubleshoot And Fix: SunJoe Pressure Washer Soap Not Working

Symptoms of a SunJoe Pressure Washer Soap Not Working

There are a few different symptoms that you may experience if your SunJoe pressure washer soap is not working properly. These include:

The soap dispenser won’t dispense soap.
The soap is not coming out of the wand properly.
The soap is not mixing with the water properly.
The soap is leaving streaks on your surfaces.

Troubleshooting a SunJoe Pressure Washer Soap Not Working

If you are experiencing any of the symptoms listed above, there are a few things you can check to troubleshoot the problem.

1. Check the soap dispenser:

The first thing you should do is check the soap dispenser to make sure that it is working properly. To do this, remove the soap dispenser from the pressure washer and check to see if there is any soap inside. If there is no soap inside, you will need to add some soap.

2. Check the soap nozzle:

The next thing you should check is the soap nozzle. The soap nozzle is located at the end of the wand. To check the soap nozzle, remove it from the wand and inspect it for any damage. If the soap nozzle is damaged, you will need to replace it.

3. Check the water pressure:

The water pressure can also affect the performance of the soap dispenser. If the water pressure is too low, the soap will not be able to mix properly with the water. To check the water pressure, turn on the pressure washer and hold the wand in front of the nozzle. The water should be coming out of the wand in a strong, steady stream. If the water pressure is too low, you may need to adjust the pressure regulator on the pressure washer.

4. Clean the soap dispenser:

If the soap dispenser is clogged, it will not be able to dispense soap properly. To clean the soap dispenser, remove it from the pressure washer and soak it in a vinegar solution for a few minutes. Then, rinse the soap dispenser thoroughly with water and dry it before reinstalling it on the pressure washer.

5. Contact SunJoe customer support:

If you have tried all of the troubleshooting steps above and your SunJoe pressure washer soap is still not working, you should contact SunJoe customer support for assistance.

How to Fix a SunJoe Pressure Washer Soap Not Working

If you have determined that the problem with your SunJoe pressure washer soap is not working is due to a faulty part, you will need to replace the part. You can purchase replacement parts for your SunJoe pressure washer from the SunJoe website or from a local hardware store.

To replace a part on your SunJoe pressure washer, follow these steps:

1. Turn off the pressure washer and disconnect it from the power source.
2. Remove the old part by following the instructions in the owner’s manual.
3. Install the new part by following the instructions in the owner’s manual.
4. Turn on the pressure washer and test it to make sure that the problem has been fixed.

Conclusion

If your SunJoe pressure washer soap is not working, you can troubleshoot the problem by checking the soap dispenser, the soap nozzle, the water pressure, and the soap dispenser itself. If you have tried all of the troubleshooting steps and the problem persists, you will need to replace the faulty part.

FAQs: SunJoe Pressure Washer Soap Not Working

Why isn’t my SunJoe pressure washer soap working?

There are a few possible reasons why your SunJoe pressure washer soap might not be working.

The soap container is empty: Make sure that the soap container is full and that the soap is properly inserted into the dispenser.

The soap is not compatible with your pressure washer: Check the manufacturer’s instructions to make sure that the soap you are using is compatible with your pressure washer.

The soap is too thick: If the soap is too thick, it will not be able to flow through the dispenser properly. Try thinning the soap with water or a surfactant.

The soap is not being dispensed properly: Make sure that the dispenser is properly connected to the pressure washer and that the nozzle is clear.

The pressure washer is not turned on: Make sure that the pressure washer is turned on and that the soap dispenser is turned on.

How do I fix my SunJoe pressure washer soap not working?

To fix your SunJoe pressure washer soap not working, try the following:

Check the soap container: Make sure that the soap container is full and that the soap is properly inserted into the dispenser.

Check the compatibility of the soap: Make sure that the soap you are using is compatible with your pressure washer.

Thin the soap: If the soap is too thick, thin it with water or a surfactant.

Check the dispenser: Make sure that the dispenser is properly connected to the pressure washer and that the nozzle is clear.

Turn on the pressure washer: Make sure that the pressure washer is turned on and that the soap dispenser is turned on.

What kind of soap do I use for my SunJoe pressure washer?

You can use any kind of soap that is compatible with your pressure washer. However, some soaps are better suited for certain tasks than others. For example, a detergent-based soap is better for cleaning concrete, while a degreaser-based soap is better for cleaning oil stains.

Here are some tips for choosing the right soap for your SunJoe pressure washer:

Consider the type of surface you will be cleaning:

Consider the type of dirt or grime you will be removing:

Consider the strength of the soap you need:

How do I use soap with my SunJoe pressure washer?

To use soap with your SunJoe pressure washer, follow these steps:

1. Fill the soap container with the desired amount of soap.
2. Insert the soap container into the dispenser.
3. Turn on the pressure washer and select the soap setting.
4. Point the spray nozzle at the surface you want to clean and start spraying.
5. Move the spray nozzle back and forth until the surface is clean.

How often should I clean my SunJoe pressure washer?

You should clean your SunJoe pressure washer after each use to prevent build-up of dirt and grime. To clean your pressure washer, follow these steps:

1. Turn off the pressure washer and disconnect the hose.
2. Remove the detergent bottle and spray nozzle.
3. Rinse the pressure washer with water.
4. Use a brush to clean the detergent bottle and spray nozzle.
5. Reattach the detergent bottle and spray nozzle.
6. Turn on the pressure washer and test it to make sure it is working properly.

You May Like to Read: Troy Bilt 2800 Psi Pressure Washer Soap Dispenser Not Working